Jeep 2005 Wrangler User Manual

TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE..

over the sport bar. As the header reaches the top, locatethe 2 bow and push it up and over the sport bar.2. Move to the side of the vehicle and pull t

3. Unclip and move the sun visor to the side. 4. Open the header latches and engage the hook on eachside into the windshield slot.UNDERSTANDING THE FE

5. Grasp the drip rail retainer and untuck them from thedoor frame.NOTE: Do not tuck the drip rails into the door frame atthis time.6. Move to the rea

7. Align the sail panel retainer to the edge of the bodys-ide retainer at the rear. Tuck the sail panel into thebodyside retainer beginning from the r

8. To install the quarter window, affix the rear corner ofthe window temporarily to the Velcro威. Start and zip thezipper only about 1 inch (2.5 cm). A

10. Tuck the bottom retainer of the quarter window intothe bottom retainer, beginning from the rear and workingto the front of the vehicle. Repeat thi

12. Zip in the rear window beginning from the left usingboth zipper ends. Run the upper zipper around thewindow leaving the lower zipper at the start.

14. Tuck the lower retainers of the rear window underthe tailgate clips. Reinstall the left corner if it wasuntucked to get the rear window zipper sta

16. Close the header latches and return the sun visor toit’s secured position.SOFT TOP — UNLIMITED MODELSCAUTION!•The soft top is not designed to carr

Place the vehicle in a warm area. Pull steadily on the topfabric. The vinyl will stretch back to its original size andthe top can then be snapped into

THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A Word About Your Keys ...13▫ Ignition Key ...13▫ Key-In-Ig

WARNING!•Do not drive vehicle with rear window curtain upunless side curtains are also open. Dangerousexhaust gases which can kill could enter thevehi

1. Grasp the fabric of the top above the door frame. Pulldown and out on the fabric to untuck the drip railretainers from the door frame slot. Start a

5. Grip and rotate the retainer bar up towards you torelease it from the upper portion of the tailgate clips. Theretainer bar runs along the bottom of

8. Finish unzipping the window and untuck from thedoor frameretainer at the frontof the window, repeat thisstep on the other side.NOTE: Stow clean win

10. Release the Sunrider pins to release the top bowsfrom the brackets located on both door rails. Push up andback on the bow slightly so it does not

12. As you begin to lower the top, wrapthe sail panels sothat they rest on the roof of the vehicle.13. Make sure the sides of the top are folded inwar

14. Tuck the top material between the 2 bow and theheader.15. After the top is folded down, ensure that the drip railretainers are tucked in inward as

16. After the top is folded down, tuck the check strapsinside the rear corners of the vehicle. This will keep themfrom hanging and flapping outside th

3. Begin working from the rear of the vehicle with thetailgate open. Standing to the side of the vehicle, lift thetop by the 2 bow and 3 bow over the

5. Pull the side bow forward and down. Make certaintheblocks on the side bows line up with the retainers on thedoor rails. Lock the blocks in place.NO

▫ Seat Belt Extender ...26▫ Driver And Front Passenger SupplementalRestraint Systems (SRS) — Airbags ...27▫ Child Restraint

7. Tuck the sail panel retainer into the bodyside retainer.Begin working from the rear tailgate opening and workto the corner.NOTE: This may be diffic

8. To install the quarter windows, affix the upper rearcorner of the window temporarily using the Velcro威.Next, start the zipper about 1 inch (2.5 cm)

10. Tuck the bottom retainer on the quarter window intothe bottom retainer, beginning from the rear and workingto the front of the vehicle. Repeat thi

NOTE: To assist in getting the zipper started, lay the barinside the vehicle on the right wheel well, uninstall halfof the left sail panel from the bo

13. Tuck the lower retainers on the rear window underthe tailgate clips.14. Reinstall the corner of the sail panel that was un-tucked to get the rear

16. Fully engage the header latch.17. Return the sun visors to their secure position.SUNRIDER — IF EQUIPPED (UNLIMITED MODELSONLY)NOTE: If you are goi

To Raise1. Grasp the drip rail retainers and untuck both of themstarting at the rear of the door frame slot. Repeat this onthe other side.2. Unclip an

4. Grasp the header and lift the top back. Make sure thematerial is folded back as shown. Secure latches to plasticretainer on header.5. Locate strap

To Lower1. Remove strap from header and sport bar.2. Release header latches from header retainer.3. Unclip and move the sun visors to the side.4. Gras

2. Fold the door frames and store the knobs and doorframes outside of the vehicle. Repeat this step for theother side.WARNING!•Use both hands to remov

A WORD ABOUT YOUR KEYSThe keys for your new vehicle are enclosed in a plasticbag with the key code number on it. If you received yourkeys without the

3. Slide door frame forward until the pin holes in the topline up with the holes in the side bar. Screw in the knobsand tighten, beginning with the fr

If required for certain off-road uses, the side bars can beremoved and the windshield folded down. However, theprotection afforded by these features i

WARNING!Carefully follow these warnings to help protect againstpersonal injury:• Do not drive your vehicle on-road with the wind-shield down.• Do not

3. Remove the two Torx威 head screws holding each sidebar to the windshield frame. Shift the side bar inboard toclear windshield pillar molding when re

CAUTION!Do not remove the head impact foam from the sidebars, as damage to the foam may result.5. To safelystore the sidebars in yourvehicle, use four

7. Remove the black round headed windshield Torx威head screw on each side of the base of the windshield.8. Lower the windshield gently until it contact

9. Secure the windshield by passing the remaining cinchstrap, found in the glove box, through the footman hoopon the center of the hood and on the cen

REAR WINDOW FEATURES — HARD TOP ONLYRear Window DefoggerTo turn the rear window defogger on, press therocker switch. If you press the switch a secondt

Rear Window Wiper/WasherTo utilize the rear wiper, press the switch to thefirst detent. To activate the rear washer, depress theswitch to the second d

UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 Instrument Panel And Interior Controls ...141䡵 Instrument Cluster ...142䡵 Instrume

To remove the ignition key on models with a manualtransmission, depress and hold the key release button,turn the ignition key to LOCK, and remove the

▫ Radio Operation ...156▫ CD Player Operation ...159䡵 Satellite Radio — If Equipped ...163▫ System Activ

INSTRUMENT PANEL AND INTERIOR CONTROLSUNDERSTANDING YOUR INSTRUMENT PANEL 1414

INSTRUMENT CLUSTER142 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTIONYour vehicle is equipped with the instrument clusterdescribed on the following pages.1. VoltmeterIndicates available bat

7. High Beam Indicator LightThis light shows that the headlights are on highbeam. Pull the turn signal lever towards thesteering wheel to switch the h

13. Oil Pressure GaugeIndicates engine oil pressure. This gauge does notindicate oil level, and pressure varies with enginespeed, temperature and oil

Certain conditions such as a loose or missing gas cap,poor quality fuel, etc. may illuminate the light afterengine start. The vehicle should be servic

20. Anti-Lock (ABS) Warning LightAfter ignition is turned on, illuminates to indicatefunction check at vehicle start-up. If light remainson after star

23. Fuel Cap IndicatorThis symbol indicates the side of the vehiclewhere the fuel cap is located.24. Fuel GaugeThe pointer shows the level of fuel in

RADIO GENERAL INFORMATIONRadio Broadcast SignalsYour new radio will provide excellent reception undermost operatingconditions. Like anysystem, however

keys that have been programmed to the vehicle can beused to start and operate the vehicle for longer than the2 second validation time period.The Sentr

remain active for up to 45 seconds after the ignitionswitch has been turned off. Opening a vehicle front doorwill cancel this feature.SALES CODE RBK—A

the radio will continue to tune until you release thebutton. The frequency will be displayed and continu-ously updated while the button is pressed.To

Press the AUDIO button a fourth time and FADE will bedisplayed. Press the SEEK + or SEEK – to adjust thesound level between the front and rear speaker

Inserting The Compact DiscCAUTION!This CD player will accept 43⁄4inch (12 cm) discsonly. The use of other sized discs may damage theCD player mechanis

FF/TUNE/RWPress FF (Fast Forward) and the CD player will begin tofast forward until FF is released. The RW ( Reverse)button works in a similar manner.

Disc Up/Program Button 1Press the DISC up (button 1) button to play the nextavailable disc.Disc Down/Program Button 5Press the DISC down (button 5) bu

CD Diagnostic IndicatorsWhen drivingovera very rough road, the CDplayer mayskip momentarily. Skipping will not damage the disc orthe player, and play

NOTE: Power to operate the radio is controlled by theignition switch. It must be in the ON or ACC position tooperate the radio.ModePress the MODE butt

and release that button. If a button is not selected within5 seconds after pressing the SET RND button, the stationwill continue to play but will not

General InformationThis radio complies with Part 15 of FCC rules and withRSS-210 of Industry Canada. Operation is subject to thefollowing conditions:1

Important Note About ServiceA four digit PIN number is needed to service the SentryKey Immobilizer System. This number can be obtainedfrom your author

show the disc number, the track number, and index timein minutes and seconds. Play will begin at the start oftrack 1.LOAD/ EJT — LoadPress the LOAD/ E

FF/TUNE/RWPress FF (Fast Forward) and the CD player will begin tofast forward until FF is released. The RW ( Reverse)button works in a similar manner.

Program Type Radio DisplayNostalgia NostalgaOldies OldiesPersonality PersnltyPublic PublicRhythm and Blues R & BReligious Music Rel MuscReligious

TimePress the TIME button to change the display fromelapsed CD playing time to time of day.Operating Instructions - Satellite Radio Mode (IfEquipped)R

System ActivationTo activate your Sirius Satellite Radio service, call thetoll-free number 888-539-7474, or visit the Sirius web siteat www.sirius.com

mode when any other button is pushed, the ignition isturned OFF, or 5 minutes has passed since any buttonwas pushed.Selecting Satellite Mode in RBB, R

NOTE: Channels that may contain objectionablecontentcan be blocked. Contact Sirius Customer Care at 888-539-7474 to discuss options for channel blocki

Satellite AntennaTo ensure optimum reception, do not place items on theroof around the rooftop antenna location. Metal objectsplaced within the line o

5. Aloose tape should be corrected before use. To rewinda loose tape, insert the eraser end of a pencil into the tapedrive gear and twist the pencil i

RADIO OPERATION AND CELLULAR PHONESUnder certain conditions, the cellular phone being On inyour vehicle can cause erratic or noisy performance fromyou

will sound and the SKIS indicator light will begin toflash. Turn the ignition switch OFF and remove thesecond key.4. Insert a blank Sentry Key into th

Blower SwitchThe blower switch is the rotary knob to the left of thecontrols. The blower speed will increase as the knobis turned clockwise. There are

Bi-LevelOutside air comes from both instrument panel andfloor outlets. Also, a slight amount of airflow maybe noticed at the defrost outlet located at

Temperature ControlThe temperature control is the center knob located on theclimate controls. It controls the temperature of the airdelivered to the p

RecirculationSelect this position when the outside air containssmoke, odors, high humidity, or if rapid cooling isdesired. This feature allows for rec

DefrostOutside air comes from the windshield outletswith a small amount being directed through thefloor outlets. Use this setting when necessary to de

STARTING AND OPERATINGCONTENTS䡵 Starting Procedures ...178▫ Manual Transmission ...178▫ Automatic Transmission ...

䡵 Axle Lock (Tru–Lok™) — If Equipped ...195䡵 Parking Brake ...196䡵 About Your Brakes ...198䡵 Anti-Lock B

䡵 Fuel Requirements ...222▫ Reformulated Gasoline ...223▫ Gasoline/Oxygenate Blends ...223▫ MMT In Gasolin

STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belts.WARNING!Do not le

10 seconds, turn the key to the OFF position, wait 5seconds, then repeat the normal starting procedure.Extreme Cold Weather (below –20°F or –29°C)To i

To Manually Lock the Steering WheelWith the engine running, rotate the steering wheel 1/2revolution from straight ahead position, turn off theengine a

If the engine has been flooded, it may start to run, but nothave enough power to continue running when the key isreleased. If this occurs, continue cr

WARNING!Remember to disconnect the cord before driving.Damage to the 110-115 volt AC electrical cord couldcause electrocution.Use the heater when temp

WARNING!When parking your vehicle, always leave a manualtransmission in first gear and apply the parkingbrake fully to guard against vehicle movement

•Push in the clutch pedal completely when shifting.Otherwise, transmission or clutch damage may result.•When “rocking” a stuck vehicle by shifting bet

off-road driving (4L range only), which will allow crank-ing the engine without depressing the clutch, followthese steps:1. Locate the Power Distribut

WARNING!It is dangerous to shift the selector lever out of “P” or“N” if the engine speed is higher than idle speed. Ifyour foot is not firmly on the b

WARNING!Unintended movement of a vehicle could injurethose in and near the vehicle. As with all vehicles,you should never exit a vehicle while the eng

CAUTION!Before moving the shift lever out of P (Park), youmust turn the ignition from LOCK to ON so thesteering wheel and shift lever are released. Ot

When frequent transmission shifting occurs while usingOverdrive, such as when operating the vehicle underheavy load conditions (for example, in hilly

WARNING!Never use P (Park) position with an automatic trans-mission as a substitute for the parking brake. Al-ways apply parking brake fully when park

WARNING!•For personal security reasons and safety in anaccident, lock the vehicle doors when you drive aswell as when you park and leave the vehicle.•

NOTE: The transmission electronics constantly monitorthe transmission oil temperature. If the transmission getstoo hot, the transmission will change t

Operating Instructions/PrecautionsThe transfer case provides four mode positions — two(rear) wheel drive high range, four wheel drive highrange, neutr

Properoperationoffourwheeldrivevehiclesdependsontires of equal size, type, and circumference on eachwheel. Any difference will adversely affect shifti

4L PositionFour Wheel Drive Low Range — Locks the front and reardriveshafts together. Forces the front and rear wheels torotate at the same speed. Add

WARNING!Failure to engage a position completely can causetransfer case damage or loss of power and vehiclecontrol. You could have an injury accident.

AXLE LOCK (TRU–LOK™) — IF EQUIPPEDTheAxle Lock switch is located on thelower center of theinstrument panel.This feature will only activate when the fo

PARKING BRAKETo set the parking brake, pull the lever up as firmly aspossible. When the parking brake is applied with theignition ON, the BRAKE warnin

NOTE: Your vehicle has automatically adjusting rearbrakes and we do not recommend any adjustment otherthan the maintenance performed by your authorize

The parking brake should always be applied when thedriver is not in the vehicle.WARNING!•Leaving children unattended in a vehicle is dan-gerous for a

WARNING!To use your brakes and decelerate more safely, follow these tips:•Do not “ride” the brakes by resting your foot on the pedal. Thiscould overhe

you will be carrying children too small for adult-sizebelts, your seat belts can also be used to hold infant andchild restraint systems.Please pay clo

WARNING!To help avoid personal injury, follow these tips:•Never reach through the steering wheel to operatesteering column controls. Injury to your ha

regulated hydraulic pressure. The motor pump makes alow humming noise during operation, this is normal.During off-road use, loss of traction can tempo

CAUTION!The Anti-Lock Brake System is subject to possibledetrimental effects of electronic interference causedby improperly installed aftermarket radi

where additional low speed pulling power is needed.Vehicle speeds in excess of 25 mph (40 km/h) should beavoided when in 4L (Low) range.Driving Throug

Standing WaterAvoid driving in standing water deeper than 20 inches,and reduce speed appropriately to minimize wave ef-fects. Maximum speed in 20 inch

your speed. If the brakes are required to control vehiclespeed, apply them lightly and avoid locking or skiddingthe tires.WARNING!If the engine stalls

After Driving Off-RoadOff-road operation puts more stress on your vehicle thandoes most on-road driving. After going off-road it isalways a good idea

TIRE SAFETY INFORMATIONTire MarkingsNOTE:•P(Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” moldedi

Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro

EXAMPLE:Service Description:95 = Load Index—A numerical code associated with the maximum load a tire can carry.H = Speed Symbol—A symbol indicating th

normal conditions. But in a collision, the belt will lockand reduce the risk of your striking the inside of thevehicle or being thrown out.WARNING!•It

Tire Identification Number (TIN)The TIN may be found on one or both sides of the tirehowever the date code may only be on one side. Tireswith white si

Tire Loading and Tire PressureTire Placard LocationNOTE: The proper cold tireinflation pressures are listedon the lower front inside corner of the dri

LoadingThe vehicle maximum load on the tire must not exceedthe load carrying capacity of the tire on your vehicle. Youwill not exceed the tire’s load

5. Determine the combined weight of luggage and cargobeing loaded on the vehicle. That weight may not safelyexceed the available cargo and luggage loa

214 STARTING AND OPERATING

WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce treadl

more often if subject to a wide range of outdoor tempera-tures, as tire pressures vary with temperature changes.Inflation pressures specified on the l

Radial-Ply TiresWARNING!Combining radial ply tires with other types of tireson your vehicle will cause your vehicle to handlepoorly. The instability c

Overloading your vehicle, long trips in very hot weather,and driving on bad roads may result in greater wear.Replacement TiresThe tires on your new ve

Lap/Shoulder Belt Operating Instructions1. Enter the vehicle and close the door. Sit back andadjust the seat.2. The seat belt latch plate is above the

WARNING!• Do not use a tire, wheel size or rating other than thatspecified for your vehicle. Some combinations ofunapproved tires and wheels may chang

Tires may also cause the vehicle to pull left or right.Alignment will not correct this problem. See your dealerfor proper diagnosis of the problem.Imp

aggressive tread designs such as those on On/Off Roadtype tires. Rotation will increase tread life, help to main-tain mud,snow, and wettraction levels

premium gasoline will provide no benefit over highquality regular gasoline, and in some circumstances mayresult in poorer performance.Light spark knoc

CAUTION!DO NOT use gasoline containing METHANOL.Gasoline containing methanol may damage criticalfuel system components.MMT In GasolineMMT is a mangane

•The use of leaded gas is prohibited by Federal law.Using leaded gasoline can impair engine performance,damage the emission control system.•An out-of-

the vehicle is raised. Have any abnormal conditionsrepaired promptly. Until repaired, drive with all sidewindows fully open.•Keep the swing gate close

CAUTION!Damage to the fuel system or emission controlsystem could result from using an improper fuel cap(gas cap). A poorly fitting cap could let impu

WARNING!•Remove the fuel cap (gas cap) slowly to preventfuel spray from the filler neck which may causeinjury.•The volatility of some gasoline may cau

•Be sure to remove the key.CAUTION!To avoid fuel spillage and overfilling, do not “topoff” the fuel tank after filling.NOTE: When the fuel nozzle “cli

WARNING!• A belt that is buckled into the wrong buckle will notprotect you properly. The lap portion could ride toohigh on your body, possibly causing

A load equalizing hitch is recommended for loadedtrailer weights above 1,000 lbs (454 kg).CAUTION!If the trailer weighs more than 1,000 lbs (454 kg)lo

STARTING AND OPERATING 2315

NOTE: Refer to “Recommended Fluids, Lubricants, andGenuine Parts” in Section 7 for axle differential lubrica-tion specifications for towing.RECREATION

5. Shift automatic transmission into D (Drive) or manualtransmission into gear.6. Release brake pedal and ensure that there is no vehiclemovement.7. S

NOTE: When shifting out of transfer case N (Neutral)on automatic transmission equipped vehicles, turningthe engine off may be required to avoid gear c

WHAT TO DO IN EMERGENCIESCONTENTS䡵 Hazard Warning Flasher ...236䡵 If Your Engine Overheats ...237䡵 Jacking And Tire Chang

HAZARD WARNING FLASHERThe flasher switch is on top of the steering column, justbehind the steering wheel. Depress the switch and bothcluster indicator

Do not use this emergency warning system when thevehicle is in motion. Use it when your vehicle is disabledand is creating a safety hazard for other m

JACKING AND TIRE CHANGINGWARNING!•Getting under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you.You could be crus

Spare Tire StowageTo remove the spare tire from the carrier, remove the tirecover, if equipped, and remove the lug nuts with the lugwrench turning the

WARNING!•A lap belt worn too high can increase the risk ofinternal injury in a collision. The belt forces won’tbe at the strong hip and pelvic bones,

•Block both the front and rearof the wheel diagonally oppo-site of the jacking position.For example, if changing theright front tire, block the leftre

and enough clearance is obtained to install the spare tire.Minimum tire lift provides maximum stability.WARNING!Raising the vehicle higher than necess

JUMP STARTINGWARNING!To prevent personal injury or damage to clothing, donot allow battery fluid to contact eyes, skin, orfabrics. Do not lean over a

1. Attach one end of the jumper cable to the positiveterminal of the discharged battery and the other end ofthe same cable to the positive terminal of

4. After the engine is started or if the engine fails to start,the cables must be disconnected in the following order:a. Disconnect the negative cable

MAINTAINING YOUR VEHICLECONTENTS䡵 2.4L Engine ...248䡵 4.0L Engine ...249䡵 Onboard Diagnostic System —

▫ Air Conditioner Maintenance ...262▫ Power Steering Fluid Check ...263▫ Driveline And Steering ComponentLubrication ...

▫ Front Side Marker ...292▫ Front Fog Light ...292▫ Rear Tail, Stop, Turn Signal, And Back-UpLights ...

2.4L ENGINE248 MAINTAINING YOUR VEHICLE

4.0L ENGINEMAINTAINING YOUR VEHICLE 2497

WARNING!A frayed or torn belt could rip apart in a collisionand leave you with no protection. Inspect the beltsystem periodically, checking for cuts,

ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor

EMISSIONS INSPECTION AND MAINTENANCEPROGRAMSIn some localities, it may be a legal requirement to passan inspection of your vehicle’s emissions control

ignition key or start the engine. This means that yourvehicle’s OBD system is not ready and you should notproceed to the I/M station.b. The MIL will n

NOTE: Intentional tampering with emissions controlsystems can result in civil penalties being assessedagainst you.WARNING!You can be badly injured wor

The best time to check the engine oil level is about 5minutes after a fully warmed engine is shut off, or beforestarting the engine after it has sat o

•More than 50% of your driving is at sustained highspeeds during hot weather, above 90°F (32°C)•Taxi, Police, or delivery service (commercial service)

Engine Oil Viscosity (2.4L Engines)SAE 5W-30 engine oil is recommended for all operatingtemperatures. This engine oil improves low tempera-ture starti

Materials Added To Engine OilsThe manufacturer strongly recommends against the ad-dition of any additives (other than leak detection dyes) toengine oi

Special tools are required to properly measure tensionand to restore belt tension to factory specifications. Also,check belt routing to make sure ther

WARNING!A hot exhaust system can start a fire if you park overmaterials that can burn. Such materials might begrass or leaves coming into contact with

Seat Belts And Pregnant WomenWe recommend that pregnant women use seat beltsthroughout their pregnancy. Keeping the mother safe isthe best way to keep

Engine Timing Belt — 2.4L EngineReplace the engine timing belt at the intervals describedin the appropriate maintenance schedule.Ignition Wiring Syste

WARNING!The air cleaner can provide protection in the case ofengine backfire. Do not remove the air cleanerunless it is necessary for repair or mainte

To determine the battery charge, check the battery testindicator (if equipped) on top of the battery. Refer to theillustration.CAUTION!It is essential

WARNING!•Use only refrigerants and compressor lubricantsapproved by the manufacturer for your air condi-tioning system. Some unapproved refrigerants a

WARNING!Fluid level should be checked on a level surface withthe engine off to prevent injury from moving parts,and to insure accurate fluid level rea

amount of a high quality lubricant such as Mopar威 LockCylinder Lubricant directly into the lock cylinder.Windshield Wiper BladesClean the rubber edges

WARNING!Commercial windshield washer solvents are flam-mable. They could ignite and burn you. Care mustbe exercised when filling or working around the

system should be drained, flushed and refilled with freshantifreeze/coolant. Check the front of theA/C condenser(if equipped) or radiator for any accu

CAUTION!•Mixing of antifreeze/coolant other than the speci-fied HOAT antifreeze/coolant may result in de-creased corrosion protection and engine damag

Use only high purity water such as distilled or deionizedwater when mixing the water/antifreeze (coolant) solu-tion. The use of lower quality water wi

Driver And Front Passenger SupplementalRestraint Systems (SRS) — AirbagsThis vehicle has front airbags for both the driver andfront passenger as a sup

children, do not store ethylene glycol based antifreeze/coolant in open containers or allow it to remain inpuddles on the ground. If ingested by a chi

coolant needs to be added, contents of coolant recov-ery bottle must also be protected against freezing.•If frequent antifreeze/coolant additions are

are present. Components should be replaced immedi-ately if there is any evidence of degradation that couldcause failure.Brake SystemIn order to assure

WARNING!Worn brake hoses can burst and cause brake failure.You could have an accident. If you see any signs ofcracking, scuffing, or worn spots, have

should be checked when pads are replaced. However,low fluid level may be caused by a leak and a checkupmay be needed.Use only manufacturer’s recommend

CAUTION!Using a transmission fluid other than the manufac-turer’s recommended fluid may cause deteriorationin transmission shift quality and/or torque

(cross-hatched area) on the oil level indicator. The fluidlevel indicator should be in the COLD region at 70° F (21°C) fluid temperature.If the fluid

Frequency of Fluid ChangeUnder normal operating conditions, the fluid installed atthe factory will give satisfactory lubrication for the life ofthe ve

CAUTION!When replacing plugs, do not overtighten. You coulddamage them and cause them to leak.Selection of LubricantUse only manufacturer’s recommende

Selection of LubricantUse only manufacturer’s recommended fluid, refer toRecommended Fluids, Lubricants, and Genuine Parts forcorrect fluid type.Appea

Airbags inflate in moderate to high speed impacts.Alongwith the seat belts, front airbags work with the instru-ment panel knee bolsters to provide imp

Washing•Wash your vehicle regularly. Always wash your ve-hicle inthe shade usinga mild car washsoapand rinsethe panels completely with clear water.•If

•Be especially careful when washing the windows byfollowing the directions for “Care of Fabric Top Win-dows.”WASHING — Always use mild soap suds, luke

Soft Top Zipper Cleaner and Lubricant to ease zipperoperation. Before applying, make sure the zipper teethare clear of sand, mud, and other materials.

Do not use scouring pads or metal polishes. Avoidautomatic car washesthat use acidic solutionsor harshbrushes that may damage the wheels’ protective f

WARNING!Only remove the carpet for cleaning purposes. Itprovides insulation against high floor pan tempera-tures. You or your passengers could be burn

Seat Belt MaintenanceDo not bleach, dye or clean the belts with chemicalsolvents or abrasive cleaners. This will weaken the fabric.Sun damage will als

FUSE PANELInterior FusesThe fuse panel is located behind the glove box.To access the fuse panel the glove box must be removed.It is removed by slippin

Cavity Fuse Description1 20 Amp Yel-lowPark Lights, Skim (SentryKey)2 20 Amp Yel-lowStop Lights3 20 Amp Yel-lowSubwoofer System4 10 Amp Red Door Switc

Underhood Fuses (Power Distribution Center)Your vehicle is equipped with an electrical power distri-bution center located in the engine compartment ne

Cavity Fuse/Color Description13 40 Amp Green Accessories14 Open15 50 Amp Red IOD16 Open17 20 Amp Yellow Power18 20 Amp Yellow Horn19 20 Amp Yellow Fog

You should read the instructions provided with yourchild restraint to makesure that you are using it properly.2. All occupants should use their lap an

VEHICLE STORAGEIf you are leaving your vehicle dormant for more than 21days you may want to take steps to protect your battery.You may:•Remove Cartrid

Fog Lights... H3Front Park/Turn Lights (2) ... 3157Front Side Marker Lights (2) ... 168orW3WHeadlights

4. Remove and replace the lamp.Front Park/Turn Signal1. Reach under the front fender and locate the frontpark/turn signal socket.2. Turn the socket as

3. Squeeze the bulb/element spring retainer from thereflector.4. Disconnect the electrical connector.CAUTION!Do not touch the new bulb with your finge

Rear Tail, Stop, Turn Signal, and Back-Up Lights1. Remove the screws attaching the lens to the tailighthousing.2. Separate the lens from the housing.3

FLUID CAPACITIESU.S. MetricFuel (Approximate) 19 Gallons 71.9 LitersEngine Oil with Filter2.4 Liter Engine (SAE 5W-30, API Certified Engine Oil) 5 Qts

RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant Mopar威 Antifreeze/Coolant 5 Year/100,0

ChassisComponent Fluid, Lubricant, or Genuine PartAutomatic Transmission Mopar威 ATF+4 Automatic Transmission Fluid or equivalent.Manual Transmission M

Component Fluid, Lubricant, or Genuine PartBrake Master Cylinder Mopar威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703brake fluid is

MAINTENANCE SCHEDULESCONTENTS䡵 Emission Control System Maintenance ...300䡵 Maintenance Schedules ...300▫ Schedule “B” ...

INTRODUCTIONCONTENTS䡵 Introduction ...4▫ Roll Over Warning ...4䡵 How To Use This Manual ...7䡵

•Driver Airbag•Passenger Airbag•Steering Wheel And Column•Instrument Panel•Crash Sensor•Interconnecting Wiring•Knee Impact BolstersHow The Airbag Syst

EMISSION CONTROL SYSTEM MAINTENANCEThe “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified toassure t

•Off-road or desert driving•If equipped for and operated with E-85 (ethanol)fuel.NOTE: If ANY of these apply to you then change yourengine oil every 3

Once a Month•Check the tire pressure and look for unusual wear ordamage.•Inspect the battery and clean and tighten the terminalsas required.•Check the

Schedule “B”Follow this schedule if you usually operate your vehicleunder one or more of the following conditions.•Day or night temperatures are below

Miles 3,000 6,000 9,000 12,000 15,000(Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000)Change the engine oil and engine oil filter, if notreplac

Miles 18,000 21,000 24,000 27,000 30,000(Kilometers) (29 000) (34 000) (38 000) (43 000) (48 000)Change the engine oil and engine oil filter, if notre

Miles 33,000 36,000 39,000 42,000 45,000(Kilometers) (53 000) (58 000) (62 000) (67 000) (72 000)Change the engine oil and engine oil filter, if notre

Miles 48,000 51,000 54,000 57,000 60,000(Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000)Change the engine oil and engine oil filter, if notre

Miles 48,000 51,000 54,000 57,000 60,000(Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000)Inspect the drive belt and replace as needed. Notrequ

Miles 63,000 66,000 69,000 72,000 75,000(Kilometers) (101 000) (106 000) (110 000) (115 000) (120 000)Change the engine oil and engine oil filter, if

WARNING!Ignoring the “Airbag Warning Light” in your instru-ment panel could mean you won’t have the airbagsto protect you in a collision. If the light

Miles 78,000 81,000 84,000 87,000 90,000(Kilometers) (125 000) (130 000) (134 000) (139 000) (144 000)Change the engine oil and engine oil filter, if

Miles 93,000 96,000 99,000 102,000 105,000(Kilometers) (149 000) (154 000) (158 000) (163 000) (168 000)Change the engine oil and engine oil filter, i

Miles 108,000 111,000 114,000 117,000 120,000(Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000)Change the engine oil and engine oil filter

Miles 108,000 111,000 114,000 117,000 120,000(Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000)Inspect the drive belt and replace as neede

Schedule “A”Miles 6,000 12,000 18,000 24,000 30,000(Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000)[Months] [6] [12] [18] [24] [30]Change the

Miles 36,000 42,000 48,000 54, 000(Kilometers) (58 000) (67 000) (77 000) (86 000)[Months] [36] [42] [48] [54]Change the engine oil and engine oil fil

Miles 60,000 66,000 72,000 78,000(Kilometers) (96 000) (106 000) (115 000) (125 000)[Months] [60] [66] [72] [78]Change the engine oil and engine oil f

Miles 60,000 66,000 72,000 78,000(Kilometers) (96 000) (106 000) (115 000) (125 000)[Months] [60] [66] [72] [78]Flush and replace the engine coolant/a

Miles 84,000 90,000 96,000 102, 000(Kilometers) (134 000) (144 000) (154 000) (163 000)[Months] [84] [90] [96] [102]Change the engine oil and engine o

Miles 108,000 114,000 120,000(Kilometers) (173 000) (182 000) (192 000)[Months] [108] [114] [120]Change the engine oil and engine oil filter. X X XRot

If you do have a collision which deploys the airbags, anyor all of the following may occur:•The nylon airbag material may sometimes cause abra-sions a

Miles 108,000 114,000 120,000(Kilometers) (173 000) (182 000) (192 000)[Months] [108] [114] [120]Flush and replace the engine coolant/anti-freeze, if

IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 Suggestions For Obtaining Service For YourVehicle ...322▫ Prepare For The Appointm

SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with

technicians, special tools, and the latest information toassure your vehicle is fixed correctly and in a timelymanner.This is why you should always ta

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY)To assist customers who have hearing difficulties, themanufacturer has installed specia

We appreciate that you have made a major investmentwhen you purchased your new vehicle. Your dealer hasalso made a major investment in facilities, too

U.S. ONLY326 IF YOU NEED CONSUMER ASSISTANCE

MOPAR姞 PARTSMopar威 fluids, lubricants, parts, and accessories areavailable from your dealer. They will help you keep yourvehicle operating at its best

PUBLICATION ORDER FORMSTo order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Ex

Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143(Canada)OrVisit us on the World Wide Web at:www.techauthority.daimlerchrysler.com orwww.daiml

Maintaining Your Airbag SystemWARNING!•Modifications to any part of the airbag systemcould cause it to fail when you need it. You couldbe injured beca

INDEX10

About Your Brakes ...198ABS (Anti-Lock Brake) System ...147,200Add-A-Trunk ...72Adding Washer Flu

Voltmeter ...143Belts, Drive ...257Belts, Seat ...20Body Mechanism Lubric

Child Restraint ...34,38,41Child Restraint Tether Anchors ...37,38Climate Control ...169Clock ...

Dimmer Switch, Headlight ...63DipsticksOil (Engine) ...253Disabled Vehicle Towing ...244Disposal

Oil Filter ...257Oil Pressure Gauge ...145Oil Selection ...295Overheating ...

Front Axle ...278Fuel ...222Filler Cap ...226Filter ...

Heater, Engine Block ...180High Beam Indicator ...144Holder, Cup ...70Hood Release ...

Lead Free Gasoline ...222Lights ...61Airbag ...33,145Anti-Lock ...

Child RestraintEveryone in your vehicle needs to be buckled up all thetime-babies and children, too. Every state in the UnitedStates and all Canadian

Lower Anchors and Tether for CHildren(LATCH) ...37,38Lubrication, Body ...264Maintenance, Airbag ...

Filter ...257Identification Logo ...255Materials Added to ...257Recommendation ...

Recommended Fluids, Lubricants and GenuineParts ...296Recreational Towing ...232Shifting into Transfer

Tilting ...57Selection of Oil ...255Sentry Key ...14Sentry Key Programming

Storage, Vehicle ...290Storing Your Vehicle ...290Supplemental Restraint System - Airbag ...27Tachometer

Hitches ...222Transfer Case ...277Four-Wheel-Drive Operation ...191Maintenance ...

Windshield, Folding ...130Windshield Washers ...64,265Fluid ...265Windshield Wiper Bla

NOTES

NOTES

NOTES

•The rearward-facing infant carrier is for babies weigh-ing up to about 20 lbs (9 kg), and one year old or more.The infant restraint must NEVER be use

NOTES

NOTES

NOTES

WARNING!•Improper installation can lead to failure of aninfant or child restraint. It could come loose in acollision. The child could be badly injured

portion of the lap/shoulder belt, or on the free end ofthe lap belt to tighten the belt. The cinching latch platewill keep the belt tight, however, an

introduced over a period of years, child restraint systemshaving attachments for those anchorages will continue toalso have features for installation

In addition, there are tether strap anchorages behind therear seat (on the floor behind each rear outboard seatingposition).Rear Seat Latch AnchorsRea

INTRODUCTIONThank you for selecting a Jeep威 Wrangler and welcome toour worldwide family.This is a specialized utility vehicle designed for bothon-road

Many, but not all restraint systems will be equipped withseparate straps on each side, with each having a hook orconnector for attachment to the lower

Installing Child Restraints Using the Vehicle SeatBeltThe passengerseat belts areequipped with cinching latchplates, which are designed to keep the la

To attach a child restraint tether strap:For the rear outboard seating positions, route the tetherover the rear seat and attach to the rear floor teth

WARNING!An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchor positions directl

ENGINE BREAK-IN RECOMMENDATIONSA long break-in period is not required for the engine inyour new vehicle.Drive moderately during the first 300 miles (5

garage, and never sit in a parked vehicle with theengine running for a extended period. If the vehicle isstopped in an open area with engine running f

have it serviced. If the light stays on or comes on whiledriving, have the system checked by an authorizeddealer.DefrostersCheck operation by selectin

UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 Mirrors ...50▫ Inside Day/Night Mirror ...50▫Inside Auto

▫ Parking Lights, Instrument Panel Lights, AndHeadlights ...62▫ Lights-On Reminder ...63▫ Headlight Dimmer Sw

▫ Console Storage Compartment — If Equipped . .72▫ Add-A-Trunk™ — If Equipped ...72䡵 Dual Top — If Equipped ...73▫ Removing Th

Do not attempt sharp turns or abrupt maneuvers or otherunsafe driving actions that can cause loss of vehiclecontrol. Failure to operate this vehicle s

MIRRORSInside Day/Night MirrorThe mirror should be adjusted to center on the viewthrough the rear window. A two-point pivot systemallows for horizonta

CAUTION!To avoid damage to the mirror during cleaning,never spray any cleaning solution directly onto themirror. Apply the solution onto a clean cloth

Compass CalibrationAutomatic CalibrationOnce calibrated, the compass has the ability to self-correct for changes in magnetic field to keep the compass

Compass Variation AdjustmentCompass Variance is the difference between magneticnorth and geographic north. In some areas of the country,the difference

To set the variance: Turn the ignition ON, and press andhold the center button for 3 to 6 seconds. The lastvariance zone number will be displayed. Eac

WARNING!•Vehicles and other objects seen in the right sideconvex mirror will look smaller and farther awaythan they really are. Relying too much on yo

Front Seat Adjustment — ReclineTo adjust seatback, lift lever, lean back, and release leverat desired position. To return seatback, lift the lever, le

Tilting Front SeatsPush the lever upward on the seatback to tilt the entireseat forward.Fold And Tumble Rear SeatTo expand the cargo area:1. Slide sea

3. Slowly flip the entire seat forward.4. When completed, return seat to it’s normal position.Removing the Rear SeatWARNING!•It is extremely dangerous

•Press down on release bar on each side, and pull seatout and away from lower bracket.•Remove seat from the vehicle.Replacing the Rear SeatReverse ste

Operating this vehicle at excessive speeds or whileintoxicated may result in loss of control, collision withother vehicles or objects, going off the r

TO OPEN AND CLOSE THE HOODTo open hood, first release both hood latches.Next, locate handle in middle of the front end of thehood. Insert hand into ga

To close the hood, remove the support rod from theradiator support and place it in the retaining clip. Lowerthe hood slowly, then let it drop the last

Multi-Function Control LeverThe multi-function control lever controls the operation ofthe parking lights, headlights, headlight beam selection,passing

NOTE: If the driver’s door is left open, and the head-lights or parking lights are left on, the “High BeamIndicator Light” will flash and a chime will

bulb. If an indicator fails to light when the lever ismoved, it would suggest that the fuse or indicator bulb isdefective.NOTE: A tone will chime if t

Windshield Wiper OperationMove the lever upwardto theseconddetentforLOspeedwiper operation, or to the third detent for HI speedoperationWindshield Was

TILT STEERING COLUMNTo tiltthe column, push down onthe lever below theturnsignal control and move the wheel up or down, asdesired. Pull the lever back

To ActivatePress and release the ON·OFF button to turn the systemon. To turn the system off, press the ON·OFF buttonagain. The system should be turned

To Vary The Speed SettingWhen the Speed Control is on and set, speed can beincreased by pressing and holding the RESUME/ACCELbutton. When the button i

ELECTRICAL POWER OUTLETTo the right of the cigar lighter (if equipped) is the 12 voltpower outlet. The outlet is connected directly to thebattery, ite

WARNING!Engine exhaust, some of its constituents, and certainvehicle components contain or emit chemicalsknown to the State of California to cause can

Electrical Outlet Use With Engine OffWARNING!• Many accessories that can be plugged in draw powerfrom the vehicle’s battery, even when not in use (i.e

The rear passengers have cup holders at the rear of thecenter console.STORAGEGlove CompartmentTo open the glove compartment, pull the latch up.Rear Cu

Console Storage Compartment — If EquippedTo unlock, insert key and turn. To open, press the latchbutton.Add-A-Trunk™ — If EquippedThe factory-installe

DUAL TOP — IF EQUIPPEDIf your vehicle is equipped with a Dual Top, you mustremove one of the tops from the vehicle. The soft topwas installed at the f

4. Using a rubber mallet, carefully tap the knuckles fromthe outside edge. This will disconnect the bow assemblyfrom the pivot bracket. Remove the sof

6. Reinstallthehard top. Refer to “HardTop Installation”in this section.Installing the Soft TopNOTE: The following procedures are for first time setup

4. If the soft top has been removed, follow these steps toreinstall the soft top. If the soft top is on the vehicle,proceed to step #5.a. If the pivot

5. Unsnap and remove the black boot cover. This covershould be discarded. It was intended as a protectivecover for shipping only.NOTE: Avisual instruc

11. Working from the rear of the vehicle with the tailgateopen, lift theplastic header (with latches)up and over thesport bar. As the header reaches t

13. Unclip and move the sun visor to the side. 14. Open the header latches and engage the hooks oneach side into the windshield slot.NOTE: Do not latc

VEHICLE IDENTIFICATION NUMBERThe vehicle identification number (VIN) is found on astamped plate located on the left front corner of theinstrument pane

require you to pull some of the fabric down and aroundthe corners. Repeat this step for the other side.NOTE: Do not tuck the drip rail retainers into

attaching it with the Velcro威. Exit the vehicle, and go tothe rearof the vehicle. Fold the rear seat andsitintherearcargo area facing rearward. Look u

NOTE: This may be difficult due to fabric tension. Ifdifficulty is experienced with fabric tension, place yourhand on top of the 3 bow and gently pull

20. Tuck in the bottom retainers on the quarter windowsinto the bodyside retainer, beginning from the rear andworking to the front of the vehicle. Rep

22. Zip the rear window beginning from the left usingboth zipper ends. Run the upper zipper around thewindow to the right side leaving the lower zippe

24. Tuck the lower retainers on both sides of the rearwindow under the tailgate clips. Reinstall the left sailpanel if it was untucked to get the rear

26. Close the header latches and return the sun visor toit’s secure position.HARD TOPCAUTION!•The hard top is not designed to carry any addi-tional lo

Hard Top Removal1. Fold down the sun visors and move them to the side.2. Unlatch the two hard top latches located at the top ofthe windshield.3. Unbol

NOTE: On a dual top vehicle, the two rear and centernuts are retained onto the bodyside.4. Open both doors.5. Open tailgate all the way to ensure clea

7. Disconnect the washer hose and install the tetheredcap.CAUTION!Make sure storage cap is installed to prevent foreignmaterials from entering tube an

VEHICLE MODIFICATIONS / ALTERATIONSWARNING!Any modifications or alterations to this vehiclecould seriously affect its roadworthiness and safetyand may

NOTE: If the red latch on the connector is locked, pushthe red latch to the right until you can only see the latchon one end (right) of the connector.

SOFT TOPCAUTION!•The soft top is not designed to carry any addi-tional loads such as roof racks, spare tires, build-ing, hunting, or camping supplies,

CAUTION!•Do not run a fabric top through an automatic carwash. Window scratches and wax build up mayresult.•Do not lower the top when the temperature

etc., clean them with a mild soap solution and a smallbrush. Cleaning products are available through yourauthorized dealer.1. If your vehicle has half

3. Unclip and move the sun visor to the side.4. Release the header latches and leave the hooks in thewindshield slots.5. Open the tailgate, partially

6. Pulltheretainer bar straight out from the tailgate clips.•Remove the rear window entirely. This is done byunzipping the window by bringing both the

8. Finish unzipping the window and untuck from thedoor frameretainer at the frontof the window, repeat thisstep on the other side.NOTE: Stow clean win

10. Completely release the hooks on the rear side of thewindshield. Grasp the side bow behind the header andlift top back.11. As you begin to lower th

Tuck the top material between the 2 bow and the 3 bowas it folds.13. Tuck the top material between the 2 bow and theheader.98 UNDERSTANDING THE FEATUR

14. After the top is folded down, ensure that the drip railretainers are tucked in inward as shown. This is to avoidunnecessary wear to the fabric.15.