TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE..
NOTE: If the driver’s door is left open, and the head-lights or parking lights are left on, the “High BeamIndicator Light” will flash and a chime will
If either light remains on and does not flash, or there is avery fast flash rate, check for a defective outside lightbulb. If an indicator fails to li
Windshield Wiper OperationMove the leverupwardto the second detentfor LOspeedwiper operation, or to the third detent for HI speedoperationWindshield W
TILT STEERING COLUMNTo tilt the column, push down on the lever under themulti-function control lever and move the wheel up ordown, as desired. Pull th
ELECTRONIC SPEED CONTROL — IF EQUIPPEDWhen engaged, this device takes over the acceleratoroperation at speeds greater than 35 mph (56 km/h). Thespeed
To Set At A Desired SpeedWhen the vehicle has reached the desired speed, pressdown on the lever and release. Release the acceleratorand the vehicle wi
To decrease speed while speed control is ON, push downand hold “SET DECEL”. Release the lever when thedesired speed is reached, and the new speed will
On steep hills, a greater speed loss or gain and/or morefrequent downshifts (auto transmission only) may occurso it may be preferable to drive without
TCS (Traction Control System)This system monitors the amount of wheelspin ofeach ofthe driven wheels. If wheel spin is detected, brakepressure is appl
WARNING!BAS (Brake Assist System) cannot prevent the natu-ral laws of physics from acting on the vehicle, nor canit increase the traction afforded by
THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A Word About Your Keys ...14▫ Ignition Key Removal ...14▫ Key-In-I
NOTE: Anytime the ESP system is in the “Full Off”mode, ERM is disabled. Refer to ESP (Electronic StabilityProgram) for a complete explanation of the a
•Understeer - when the vehicle is turning less thanappropriate for the steering wheel position.The ⬙ESP/TCS Indicator Light⬙ located in the instrument
High Range (4WD Models) or 2WD ModelsOnThis is the normal operating mode for ESP in 4WD highrange and in 2WD vehicles. Whenever the vehicle isstarted
NOTE: To improve the vehicle’s traction when drivingwith snow chains, or starting off in deep snow, sand, orgravel, it may be desirable to switch to t
WARNING!With the ESP switched off, the enhanced vehiclestability offered by ESP and ERM are unavailable. Inan emergency evasive maneuver, the ESP and
WARNING!With the ESP switched off, the enhanced vehiclestability offered by ESP and ERM are unavailable. Inan emergency evasive maneuver, the ESP and
ELECTRICAL POWER OUTLETThis vehicle has two auxiliary power outlets that canprovide up to 20 Amps of current for accessories de-signed for use with th
Electrical Outlet Use With Engine OffWARNING!•Many accessories that can be plugged in draw powerfrom the vehicle’s battery, even when not in use (i.e.
The rear passengers have cup holders at the rear of thecenter console.STORAGEConsole Storage CompartmentTo lock or unlock, insert ignition key and tur
Rear Storage CompartmentThe rear storage compartment cover is held by a springloaded latch. In order to remove the rear storage com-partment cover, us
▫ Using The Panic Alarm ...22▫ To Turn Off “Flash Lights With Lock” ...22▫ Programming Additional Transmitters ...23▫ General
DUAL TOP — IF EQUIPPEDIf your vehicle is equipped with a Dual Top, you mustremove one of the tops from the vehicle. If the soft topis removed, the piv
3. Remove the soft top bow assembly pivot bracketscrews (2 per side) using a #T30 Torx威 head driver.4. Using a rubber mallet, carefully tap the knuckl
5. Unzip the zipper on the sport bar cover to expose thepivot brackets. Remove the brackets using a #T30 Torx威head driver. Recover and re-zip the spor
3. Install the door frames. Refer to “Door Frame” in thissection.4. If the soft top has been removed, follow these steps toreinstall the soft top. If
c. Tap the knuckles on the side with a rubber mallet toreattach them to the metal pivot brackets.d. Screw the pivot screws back into place using a #T3
5. Unsnap and remove the black boot cover. This covershould be discarded. It was intended as a protectivecover for shipping only.NOTE: A visual instru
Front Panel(s) RemovalNOTE: Left panel must be removed before removingright panel.1. Fold down the sun visor, and move to the side.2. Turn center l-sh
4. Turn rear fasteners (knobs) (located on overheadspeaker bar assembly) counter-clockwise until they canbe removed.5. Unlatch the header panel latch
Front Panel(s) InstallationNOTE: The front panel (s) must be positioned properlyto ensure sealing. Set the panels on the windshield frameso that there
2. Install right panel first, then the left panel.3. Reinstall panel(s) using the same steps for removal inreverse order.Rear Panel Removal1. Remove b
▫ Child Restraint ...64䡵 Engine Break-In Recommendations ...77䡵 Safety Tips ...78▫ Exhaust Gas .
6. Locate the wiring harness at the rear left side corner ofthe vehicle.7. Disconnect the washer hose and install the tetheredcap.CAUTION!Make sure st
9. Remove the hard top from the vehicle. Place on a softsurface to prevent damage.Rear Panel InstallationNOTE: If the door frames are installed from s
DOOR FRAMEWARNING!Do not drive your vehicle on-pavement with the doorframe removed as you lose the protection thesestructural elements can provide. Th
2. Place one hand on the upper rear and one hand on thefront of the door frame.3. Pull the frame towards you with your rearward handto remove the fram
Door Frame Installation (2 Door Models)1. Unfold door frame and unscrew thumbscrews.2. Set the door frame pin into the hole on top of the bodyside, be
5. Starting with the front knob, screw in and tighten bothknobs. Repeat on the other side.Door Frame Removal (4 Door Models)1. Unscrew and remove the
WARNING!Use both hands to remove the door frames. The doorframes will fold and could cause injury if both handsare not used.2. Place one hand on the u
3. Pull the frame towards you with your front hand toremove the frame from the vehicle.4. Unscrew and remove the remaining door frame at-tachment knob
6. Screw the knob back into the door frame and fold forstorage. Store in a secure location.WARNING!•Never store the door frames in your vehicle. In an
3. Position the top of the door frame against the metalsport bar and press onto the side bar making sure not topinch the material of the sports bar co
A WORD ABOUT YOUR KEYSThe keys for your new vehicle are enclosed in a plasticbag with the key code number on it. If you received yourkeys without the
door frame. Position the rear of the front door frame tolay on top of the front of the rear door frame.6. Loosely install both knobs beginning with th
SOFT TOP (2 DOOR MODELS)CAUTION!•The soft top is not designed to carry any additionalloads such as roof racks, spare tires, building,hunting, or campi
CAUTION!•Do not run a fabric top through an automatic car wash.Window scratches and wax build up may result.•Do not lower the top when the temperature
Folding Down The Soft Top1 — Header Bow 6 — Body Side Retainer2 — 2 Bow 7 — Quarter Window3 — 3 Bow 8 — Check Strap4 — Sail Panel 9 — Front Retainer —
1 — Zipper Start2 — Zipper Finish3 — Swing Gate Bar4 — Swing Gate Brackets5 — Sail Panels144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
NOTE: Clean side and rear windows before removal toassist in preventing scratching during removal of the softtop. If zippers are difficult to operate
3. Unclip and move the sun visors to the side.4. Release the header latches and leave the hooks in theloops on the windshield.5. Open the swing gate.6
•Unzip the rear window starting at the right lowercorner of the window. Pull the zipper up, across thetop and down to the left lower corner. Zipper pu
9. Once unzipped, remove side window retainers fromthe door channel and body side channel. Repeat this stepon the opposite side.10. Finish releasing t
12. The swing gate brackets do not need to be removedunless the hard top is being installed. To remove theswing gate brackets, pull the front of the b
WARNING!Leaving children in a vehicle unattended is danger-ous for a number of reasons. A child or others couldbe injured. Children should be warned n
14. Grasp the side bow behind the header, lift the top,and fold toward the rear of the vehicle.15. Tuck the fabric and the check straps between thebow
Putting Up The Soft Top1 — Header Bow 6 — Body Side Retainer2 — 2 Bow 7 — Quarter Window3 — 3 Bow 8 — Check Strap4 — Sail Panel 9 — Front Retainer — Q
1 — Zipper Start2 — Zipper Finish3 — Swing Gate Bar4 — Swing Gate Brackets5 — Sail Panels152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
1. Unclip and move the sun visors to the side.2. Install door frames,if removed. Referto “Door Frame”in this section.3. Standing on the side of the ve
5. Open the header latches and engage the hook on eachside onto the windshield loops (do not close the latches).6. If the swing gate brackets were rem
7. Move to the rear of the vehicle and gently pull the sailpanels over the rear roof bow.8. Partially install the sail panel retainers into the bodysi
9. To install the side windows, affix the window tempo-rarily by attaching to the Velcro威 in the rear corner. Startthe zipper but close only about 1 i
11. Continue closing the zipper only along the top edgeof the window.12. Insert the retainer along the bottom edge of thewindow into the bottom side c
13. Locate the black swing gate bar. Slide the swing gatebar over the receiver at the bottom inside of the rearwindow. The spongypart of the seal shou
16. Grasp the swing gate bar and position it into theswing gate brackets.17. Apply downward pressure on the top corner of therear soft top bow (3 bow)
To Release the Steering Wheel LockInsert the key in the ignition and turn the wheel slightlyto the right or left to disengage the lock.NOTE: If you tu
19. Close the header latches and return the sun visors totheir secured position.SUNRIDER — 4 DOOR MODELSNOTE: If you are going to be driving faster th
To Open1. Above the front of the rear door, place finger up intothe cut out in the plastic retainer and pull down rollingboth the front and rear retai
4. Grasp the front side bow behind the header, and liftthe top.5. Fold back the front section of the top, and gently restthe header on top of the rear
6. Fold the top material so that the plastic retainers forma “W” as shown. Enter the vehicle,and movethe materialinto two folds. Ensure that the strap
SOFT TOP (4 DOOR MODELS)CAUTION!•The soft top is not designed to carry any additionalloads such as roof racks, spare tires, building,hunting, or campi
CAUTION!• Do not run a fabric top through an automatic car wash.Window scratches and wax build up may result.• Do not lower the top when the temperatu
Folding Down The Soft Top1 — Header Bow 6 — Body Side Retainer 11 — Plastic Retainer2 — 2 Bow 7 — Quarter Window3 — 3 Bow 8 — Check Strap4 — 4 Bow 9 —
1 — Zipper Start2 — Zipper Finish3 — Swing Gate Bar4 — Swing Gate Brackets5 — Sail PanelsUNDERSTANDING THE FEATURES OF YOUR VEHICLE 1673
NOTE: Clean side and rear windows before removal toassist in preventing scratching during removal of the softtop. If zippers are difficult to operate
4. Release the header latches and hooks from the loopson the windshield frame.5. Open the swing gate.6. Before unzipping the rear window, release the
longer than 10 seconds) a fault has been detected in theelectronics and the vehicle should be serviced as soon aspossible.NOTE:•The Sentry Key Immobil
•Unzip the rear window starting at the right lowercorner of the window. Pull the zipper up, across thetop and down to the left lower corner. Zipper pu
9. Once unzipped, remove side window retainers fromthe door channel and body side channel. Repeat this stepon the opposite side.10. Finish releasing t
12. The swing gate brackets do not need to be removedunless the hard top is being installed. To remove theswing gate brackets, pull the front of the b
14. Fold back the front section of the top, and gently restthe header on top of the rear portion of the deck.15. Fold the topmaterial so that the plas
16. Release the side bows by pressing down on the latchabove the front of the rear door. Push the top rearward todisengage. Repeat this step on the ot
18. Gently slide the side bows off the door frame trackand lower the top down into the vehicle.19. Tuck the fabric and the check straps between thebow
Putting Up The Soft Top1 — Header Bow 6 — Body Side Retainer 11 — Plastic Retainer2 — 2 Bow 7 — Quarter Window3 — 3 Bow 8 — Check Strap4 — 4 Bow 9 — F
1 — Zipper Start2 — Zipper Finish3 — Swing Gate Bar4 — Swing Gate Brackets5 — Sail PanelsUNDERSTANDING THE FEATURES OF YOUR VEHICLE 1773
NOTE: Be extremely careful when putting up the softtop toprevent thedoors from gettingscratched. Itmay behelpful to open the rear doors.1. Install the
5. Insert the slider feature of the knuckles into the doorframe tracks and slide the top forward.6. Ensure that the top locks into Sunrider locking me
consists of programming a blank key to the vehicleelectronics. A blank key is one which has never beenprogrammed.NOTE: When having the Sentry Key Syst
8. Standing on the side of the vehicle, lift the top by theside bow until it rests on the windshield frame.9. Before attaching the header latches, be
10. Openthe headerlatches and engage thehook on eachside onto the windshield loops (do not close the latches).11. If the swing gate brackets were remo
13. Partially install the sail panel retainers into the bodyside channel, leaving the last three (3) inches towards therear window loose (on both side
15. Insert the front retainer of the window into the doorchannel, making sure the retainer is fully seated andproperly positioned on the door frame. F
17. Insert the retainer along the bottom edge of thewindow into the bottom side channel, beginning at thefront and working to the rear of the vehicle.
19. Install the rear window by starting both zipper endsat the lower left corner of the rear window opening.Ensure that the zippers are properly start
23. Open the doors and insert the top retainers into thechannels in the door frame above the doors, starting atthe front and work toward the rear of t
25. Close the header latches and return the sun visors totheir secured position.FOLDING WINDSHIELDThe fold down windshield and removable side bars ony
Raise thewindshield and reinstall theside bars assoon asthe task that required their removal is completed andbefore you return to on-road driving. Bot
Lowering the Windshield and Removing SideBars1. Lower the fabric top or remove the hard top followingthe instructions in this manual.NOTE: To assist i
2. This device must accept any interference that may bereceived, including interference that may cause undes-ired operation.SECURITY ALARM SYSTEM — IF
4. Remove 1 hex bolt (13mm) visible through the plastictrim on bottom side of side bar, 1 hex bolt (13mm) on theside of the side bar, and 1 hex bolt (
WARNING!You or others could be injured if you carry the sidebars loose in your vehicle. Remove the bars from thevehicle or securely store them as desc
Raising The Windshield And Replacing Side Bars1. Raise the windshield.2. Loosely attach rear of side bar to sport bar. Refer toStep 4 of “Lowering Win
5. Install the lower windshield plates with the 6 blackround headed Torx威 head screws (using a #40 Torx威 headdriver) on each side of the base of the w
If the rear wiper is operating when the ignition is turnedOFF, the wiper will automatically return to the “Park”position. When the vehicle is restarte
level at regular intervals. Fill the reservoir with wind-shield washer solvent (not radiator antifreeze) and oper-ate the system for a few seconds to
UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 Instrument Panel And Controls ...200䡵 Instrument Cluster ...201䡵 Instrument
▫ Notes On Playing MP3/WMA Files ...228▫ List Button (Disc Mode For MP3/WMAPlay) ...230▫ Info Button (Disc Mode For MP
䡵 CD/DVD Disc Maintenance ...251䡵 Radio Operation And Cellular Phones ...252䡵 Climate Controls ...252▫ Manual Hea
The Security Alarm System is designed to protect yourvehicle; however, you can create conditions where thesystem will arm unexpectedly. If you remain
INSTRUMENT PANEL AND CONTROLS200 UNDERSTANDING YOUR INSTRUMENT PANEL
INSTRUMENT CLUSTERUNDERSTANDING YOUR INSTRUMENT PANEL 2014
INSTRUMENT CLUSTER DESCRIPTIONYour vehicle is equipped with the instrument clusterdescribed on the following pages.1. Fuel GaugeThe pointer shows the
6. Front Axle Lock Indicator Light — If EquippedIndicates when the front axle lock has beenactivated.7. Seat Belt Indicator LightA warning chime and a
11. Brake Warning LightAfter ignition is turned on,illuminates toindicatefunction check at vehicle start-up. Indicates park-ing brake isapplied. Ifthe
14. Rear Axle Lock Indicator Light — If EquippedIndicates when the rear axle lock has beenactivated.15. TachometerIndicates the engine speed in revolu
20. 4WD Indicator Light — If EquippedThis light alerts the driver that the vehicle is inthe four-wheel drive mode, and the front andrear driveshafts a
can lead to tire failure. Under-inflation also reduces fuelefficiency and tire tread life, and may affect the vehicle’shandling and stopping ability.P
24. Odometer/Trip OdometerThe odometer shows the total distance the vehicle hasbeen driven.U.S. federal regulations require that upon transfer ofvehic
up on the accelerator and apply as little throttle aspossible. Be sure to adapt your speed and driving to theprevailing road conditions. The “ESP/TCS
NOTE: The line of transmission must not be blockedwith metal objects.To Unlock the Doors and Swing GatePress and release the “Unlock” button on the ke
30. Electronic Throttle Control (ETC) Warning Light —If EquippedThis light informs you of a problem with theElectronic Throttle Control System. If a p
COMPASS AND TRIP COMPUTER — IFEQUIPPEDThis feature, located on the instrument cluster (speedom-eter and tachometer), displays information on outsidete
Press and hold the left button (on the instrument cluster)for 2 to 3 seconds to switch from English to Metricdisplays.ResetPress and hold the right bu
Trip AShows the total distance traveled for trip A since the lastreset.Trip BShows the total distance traveled for trip B since the lastreset.Compass
After initial calibration, the compass will continue toautomatically update this calibration whenever the ve-hicle is in motion.Manual Compass Calibra
symbol appears. The current variance value will also bedisplayed. To change the zone, press the left button onceto increment the zone. The default is
Outside TemperatureIf the outside temperature is more than 131°F (55°C), thedisplay will show 131°F (55°C). When the outside tem-perature is less than
FM ReceptionBecause FM transmission is based on frequency varia-tions, interference that consists of amplitude variationscan be filtered out, leaving
Power Switch/Volume Control (Rotary)Press the ON/VOL control to turn the radio ON. Pressthe ON/VOL a second time to turn OFF the radio.Electronic Volu
Phone Button (UConnect™ Hands Free Phone) —If EquippedPress this button to operate the Hand Free Phone (UCon-nect™) feature (if equipped). Refer to Ha
2. While the “Lock” button is pressed (after 4 seconds),press the PANIC button. Release both buttons.The “Sound Horn On Lock” feature can be reactivat
RW/FF (Radio Mode)Pressing the rewind or fast forward button causes thetuner to search for the next frequency in the direction ofthe arrows. This feat
allow the program format type tobe selected. Many radiostations do not currently broadcast Music Type informa-tion.Toggle the Music Type button to sel
By pressing the SEEK button when the Music Type iconis displayed,the radio will be tuned to the next frequencystation with the same selected Music Typ
•Angle – Repeatedly Pressing SELECT will changethe viewing angle if supported by the DVD disc (IfEquipped).NOTE: The available selections for each of
disc). If customer wishes to select a language not listed,then scroll down and select ⬙other.⬙ Enter the countrycode using the TUNE control knob to sc
NOTE: The user will have to set these defaults beforeloading a disc. If changes are made to these settings aftera disc is loaded, changes will not be
Operation Instructions - (DISC MODE for CD andMP3/WMA Audio Play, DVD-VIDEO)The radio DVD player andmany DVD discs arecoded bygeographic region. These
Eject Button — Ejecting Compact Disc(s)Press the eject button and the push-button withthe corresponding number (1-6) where the CDwas loaded and the di
RND Button (Random Play Button) (CD MODE)Press this button while the CD is playing to activateRandom Play. This feature plays the selections on thecom
Multisession disc formats are supported by the radio.Multisession discs may contain combinations of normalCD audio tracks and computer files (includin
The “Flash Lights On Lock/Unlock” feature can bereactivated by repeating this procedure.Programming Additional TransmittersVehicles will be shipped fr
ID3 Tag information for artist, song title, and album titleare supported for version 1 ID3 tags. ID3 version 2 is notsupported by the radios.Playlist
INFO Button (DISC Mode for MP3/WMA Play)Pressing the INFO button repeatedly will scroll throughthe following TAG information: Song Title, Artist, File
TIME Button (Auxiliary Mode)Press this button to change the display from elapsedplaying time to time of day. The time of day will displayfor 5 seconds
SALES CODE RES — AM/FM STEREO RADIOWITH CD PLAYER (MP3 AUX JACK)NOTE: The radio sales code is locatedon the lower rightside of your radio faceplate.Op
to seek up and the left switch to seek down. The radiowill remain tuned to the new station until you makeanother selection. Holding either button will
Clock Setting Procedure1. Press and hold the TIME button, until the hours blink.2. Adjust the hours by turning the right side TUNEcontrol knob.3. Afte
Press the rotary TUNE control knob a second time andMID will display. Turn the TUNE control knob to theright or left to increase or decrease the Mid R
Jazz JazzNews NewsNostalgia NostalgaOldies OldiesPersonality PersnltyPublic PublicRhythm and Blues R & BReligious Music Rel MuscReligious Talk Rel
AM and FM ButtonsPress the buttons to select AM or FM Modes.SET Button — To Set the Push-Button MemoryWhen you are receiving a station that you wish t
Operation Instructions - CD MODE for CD andMP3 Audio PlayNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.NOTE: This Ra
11. A single chime will be heard.12. Repeat steps 8 through 10 to program up to sixadditional fobs.13. Turn the ignition to the OFF position.14. Your
EJECT Button - Ejecting a CDPress the EJECT button to eject the CD.If you have ejected a disc and have not removed it within10 seconds, it will be rel
AM or FM ButtonSwitches the Radio to the Radio mode.RND Button (Random Play Button)Press this button while the CD is playing to activateRandom Play. T
a number instead. With a maximum number of files,exceeding 20 folders will result in this display. With200 files, exceeding 50 folders will result in
MPEGSpecificationSampling Fre-quency (kHz)Bit Rate (kbps)MPEG-1 AudioLayer 348, 44.1, 32320, 256, 224,192, 160, 128,112, 96, 80, 64,56, 48, 40, 32MPEG
LIST Button (CD Mode for MP3 Play)Pressing the LIST button will bring up a list of all folderson the disc. Scrolling up or down the list is done bytur
TIME Button (Auxiliary Mode)Pressthis button to change the display to time of day. Thetime of day will display for 5 seconds (when ignition isoff).Ope
Operating Instructions — Satellite RadioRefer to your “Navigation User’s Manual” for detailedoperating instructions.Clock Setting ProcedureThe GPS rec
3. Highlight the appropriate time zone for you locationand press ENTER to store your selection. Select “Done”when finished.NOTE: When you are travelin
1. The Electronic Serial Number/Sirius IdentificationNumber (ESN/SID).2. Your Vehicle Identification Number.Electronic Serial Number/Sirius Identifica
•Dense tree coverage may interrupt reception in theform of short audio mutes.•Driving under wide bridges or along tall buildings cancause intermittent
Battery ReplacementThe recommended replacement battery is CR2032.NOTE:Perchlorate Material – special handling may apply,See www.dtsc.ca.gov/hazardousw
TUNE Control (Rotary)Turn the right side rotary control clockwise to increase orcounter-clockwise to decrease the channel.MUSIC TYPE ButtonPressing th
the SET button twice and SET 2 will show in the displaywindow. Each button can be set for SET 1 and SET 2. Thisallows a total of 12 Satellite channels
6. Do not expose the disc to direct sunlight.7. Do not store the disc where temperatures may becometoo high.RADIO OPERATION AND CELLULAR PHONESUnder c
Mode ControlThe mode control (left rotary knob) allows you to choosefrom several patterns of air distribution. You can selecteither a primary mode, as
you select. The fan speed increases as you move thecontrol to the right from the OFF position.Temperature ControlUse this control (right rotary knob)
Mode ControlThe mode control allows youto choose from several pat-terns of air distribution. Youcan select either a primarymode, as identified by thes
DefrostAir is directed through the windshield and sidewindow demist outlets. Use this mode with maxi-mum fan and temperature settings for best windshi
Temperature ControlUse this control to regulatethe temperature of the air in-side the passenger compart-ment. The blue area of thescale indicates cool
moisture build up inside the vehicle. For maximumdefogging, select the Outside Air position.NOTE: The “Recirculate” mode will not operate in floor,mix
smoke, perfumes, etc.) from sticking to the windows.Contaminates increase the rate of window fogging.Summer OperationAir conditioned vehicles must be
3. To assemble the transmitter case, snap the two halvestogether.NOTE: If the key fob is equipped with a screw, reinstalland tighten the screw until s
STARTING AND OPERATINGCONTENTS䡵 Starting Procedures ...265▫ Manual Transmission ...265▫ Automatic Transmission ...
▫ Shift Positions ...282▫ Shifting Procedure ...283䡵 Trac-Lok™ Rear Axle — If Equipped ...284䡵 Axle Lock (
▫ Radial-Ply Tires ...312▫ Tire Spinning ...312▫ Tread Wear Indicators ...312▫ Life Of Tire ...
▫ Trailer Towing Weights (Maximum TrailerWeight Ratings) ...335▫ Trailer And Tongue Weight ...338▫ Towing Requirements .
STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belts.WARNING!Never lea
Tip Start Feature — Automatic Transmission OnlyDo not press the accelerator. Turn the ignition key brieflyto START position, and release it. The start
CAUTION!To prevent damage to the starter, do not crank theengine for more than 15 seconds at a time. Wait 10 to15 seconds before trying again.WARNING!
If the engine has been flooded, it may start to run, but nothave enough power to continue running when the key isreleased. If this occurs, continue cr
ENGINE BLOCK HEATER — IF EQUIPPEDThe engine block heater warms engine coolant andpermits quicker starts in cold weather. Connect the cordto a standard
2. Unplug wiring harness connector under instrumentpanel.3. Unhook door strap from the body hook. Be careful notto allow door to swing fully open as m
Follow the shift pattern on the gearshift knob.NOTE: The backup lights will come on when yourvehicle is inR (Reverse)gear and the ignitionis in the ON
•Do not operate at sustained high engine or roadspeeds in lower gears. Engine damage may result.•Do not downshift into alow gear while travelingat too
Recommended Manual Transmission DownshiftingSpeedsTo prevent clutch and transmission damage, your vehicleshould be downshifted at speeds no greater th
AUTOMATIC TRANSMISSIONCAUTION!Damage to the transmission may occur if the follow-ing precautions are not observed:•Shift into P (Park) only after the
Shift Lock Manual OverrideYour vehicle may be equipped with a shift lock manualoverride. The manual override may be used in the eventthat the shift le
Brake/Transmission Interlock SystemThis system prevents you from moving the gear shift outof P (Park) and into any gear unless the brake pedal ispress
Gear RangesDO NOT race the engine when shifting from P (Park) orN (Neutral) position into another gear range.P (Park)This gear position supplements th
R (Reverse)Use this range only after the vehicle has come to acomplete stop.N (Neutral)Shift into N (Neutral) when the vehicle is standing forprolonge
When frequent transmission shifting occurs while usingOverdrive, such as when operating the vehicle underheavy load conditions (for example, in hilly
WARNING!Never use P (Park) position with an automatic trans-mission as a substitute for the parking brake. Alwaysapply parking brake fully when parked
3. Remove interior B-pillar trim access door at bottom ofB-pillar.4. Unplug wiring harness connector.5. Unhook door strap from the body hook.6. With t
Torque Converter ClutchA feature designed to improve fuel economy has beenadded to the automatic transmission of this vehicle. Aclutch within the torq
This transfer case is intended to be driven in the twowheel drive (2H) position for normal street and highwayconditions such as hard surfaced roads.In
WARNING!You or others could be injured if you leave thevehicle unattended with the transfer case in the N(Neutral) position without first fully engagi
The “4WD Indicator Light” (located in the instrumentcluster) will illuminate when the transfer case is shiftedinto the 4H position.N (Neutral) Positio
NOTE: Pausing in transfer case N (Neutral) in vehiclesequipped with an automatic transmission may requireshutting the engine OFF to avoid gear clash w
Trac-Lok™ is especially helpful during slippery drivingconditions. With both rear wheels on a slippery surface, aslight application of the accelerator
This feature will only activate when the following con-ditions are met:•Key in ignition, vehicle in 4L (Low) range.•Vehicle speed should be 10 mph (16
ELECTRONIC SWAY BAR DISCONNECT — IFEQUIPPEDYour vehicle may be equipped with an electronic discon-necting stabilizer/sway bar. This system allows grea
when activation conditions are not met. The stabilizer/sway bar should remain in on-road mode during normaldriving conditions.WARNING!Do not disconnec
WARNING!If the stabilizer/sway bar will not return to on-roadmode, vehicle stability is greatly reduced. Do notattempt to drive vehicle over 18 mph (2
DOOR LOCKSThe vacuum fluorescent (VF) display located in theodometer area displays the word “door” as an indicationof a door ajar or door not complete
OFF-ROAD DRIVING TIPSNOTE: Prior to off-road usage, the side step (ifequipped) should be removed to prevent damage.1. Remove two (2) nuts from bodysid
extreme situations such as deep snow, mud, steep in-clines, orsand whereadditional lowspeed pullingpoweris needed. Vehicle speeds in excess of 25 mph
Standing WaterAvoid driving in standing water deeper than 20 inches,and reduce speed appropriately to minimize wave ef-fects. Maximum speed in 20 inch
your speed. If the brakes are required to control vehiclespeed, apply them lightly and avoid locking or skiddingthe tires.WARNING!If the engine stalls
After Driving Off-RoadOff-road operation puts more stress on your vehicle thandoes most on-road driving. After going off-road it isalways a good idea
PARKING BRAKETo set the parking brake, pull the lever up as firmly aspossible. When the parking brake is applied with theignition ON, the “Brake Warni
(Park), otherwise the load on the transmission lockingmechanism may make it difficult to move the selector outof P (Park).WARNING!•Always fully apply
WARNING!Significant over or under-inflation of tires, or mixingsizes of tires or wheels on the vehicle can lead to lossof braking effectiveness.The An
WARNING!•Anti-lock system (ABS) cannot prevent the naturallaws of physics from acting on the vehicle, nor canit increase braking or steering efficienc
If for some reason the power assist is interrupted, it willstill be possible to steer your vehicle. Under these condi-tions, you will observe a substa
INTRODUCTIONCONTENTS䡵 Introduction ...4▫ Roll Over Warning ...5䡵 How To Use This Manual ...7䡵
Manual Door LocksThe front (2 Door Models) and rear doors (4 DoorModels) are equipped with a rocker-type interior doorlock. To lock a door when leavin
TIRE SAFETY INFORMATIONTire MarkingsNOTE:•P(Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” moldedi
Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro
EXAMPLE:Service Description:95 = Load Index—A numerical code associated with the maximum load a tire can carry.H = Speed Symbol—A symbol indicating th
Tire Identification Number (TIN)The TIN may be found on one or both sides of the tirehowever the date code may only be on one side. Tireswith white si
Tire Loading and Tire PressureTire Placard LocationTire Placard Location (2 Door Models)Tire Placard Location (4 Door Models)304 STARTING AND OPERATIN
Tire and Loading Information PlacardThis placard tells you important information about the,1) number of people that can be carried in the vehicle2) th
combined weight of occupants, cargo/luggage andtrailer tongue weight (if applicable) should never exceedthe weight referenced here.Steps for Determini
STARTING AND OPERATING 3075
WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti
2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread
Power Door Locks — If EquippedThe door lock switch is located on each front door panel.Press the switch downward to lock the doors, andupward to unloc
The pressure should be checked and adjusted as well asinspecting for signs of tire wear or visible damage at leastonce a month. Use a good quality poc
Tire pressures change by approximately 1 psi (7 kPa) per12° F (7° C) of air temperature change. Keep this in mindwhen checking tire pressure inside a
Radial-Ply TiresWARNING!Combining radial ply tires with other types of tireson your vehicle will cause your vehicle to handlepoorly. The instability c
These indicators are molded into the bottom of the treadgrooves and will appear as bands when the tread depthbecomes 1/16 inch (2 mm). When the indica
Keep unmounted tires in a cool, dry place with as littleexposure to light as possible. Protect tires from contactwith oil, grease and gasoline.Replace
CAUTION!Replacing original tires with tires of a different sizemay result in false speedometer and odometerreadings.Alignment and BalancePoor suspensi
•Install chains snugly and tighten after.6 mile (1 km) ofdriving.•Do not exceed 30 mph (48 km/h).•Drive cautiously, avoiding large bumps, potholes and
TIRE PRESSURE MONITOR SYSTEM (TPMS) — IFEQUIPPEDThe Tire Pressure Monitoring System (TPMS) will warnthe driver of a low tire pressure based on the veh
(241 kPa). If the ambient temperature is 65°F (18°C) andthe measured tire pressure is 30 psi (207 kPa), a tempera-ture drop to 20°F (-7°C) will decrea
The “Tire Pressure Monitoring Telltale Light” willilluminate in the instrument cluster, and an au-dible chime will be activated when one or more ofthe
WINDOWSPower Windows — If EquippedThe power window switches are located on the instru-ment panel center stack (below the radio). The top leftswitch co
CAUTION!The TPMS has been optimized for the originalequipment tires and wheels. TPMS pressures havebeen established for the tire size equipped on your
Under-inflation also reduces fuel efficiency and tiretread life, and may affect the vehicle’s handling andstopping ability.•The TPMS is not a substitu
Light spark knock at low engine speeds is not harmful toyour engine. However, continued heavy spark knock athigh speeds can cause damage and immediate
CAUTION!DO NOT use gasolines containing Methanol or E85Ethanol. Use of these blends may result in startingand driveability problems and may damage cri
Fuel System CautionsCAUTION!Follow these guidelines to maintain your vehicle’sperformance:•The use of leaded gasoline is prohibited by Federallaw. Usi
garage, and never sit in a parked vehicle with theengine running foran extendedperiod. If the vehicleisstopped in an open area with the engine running
CAUTION!Damage to the fuel system or emission control sys-tem could result from using an improper fuel cap(gas cap). A poorly fitting cap could let im
NOTE: Tighten the gas cap about 1/4 turn until youhear one click. This is an indication that cap is properlytightened.If the gas cap is not tighten pr
VEHICLE LOADINGCertification LabelAs required by National Highway Traffic Safety Admin-istration Regulations, your vehicle has a certificationlabel af
Tire SizeThe tire size on the Label represents the actual tire size onyour vehicle. Replacement tires must be equal to the loadcapacity of this tire s
Auto DownBoth the driver and front passenger window switch hasan “Auto Down” feature. Press the window switch pastthe first detent, release, and the w
Improper weight distributions can have an adverse effecton the way your vehicle steers and handles and the waythe brakes operate.CAUTION!Do not load y
Gross Trailer Weight (GTW)The Gross Trailer Weight (GTW) is the weight of thetrailer plus the weight of all cargo, consumables andequipment (permanent
Frontal AreaThe maximum height and maximumwidth ofthe frontofa trailer.Trailer Sway ControlThe trailer sway control is a telescoping link that can bei
WARNING!An improperly adjusted Weight Distributing Hitchsystem may reduce handling, stability, braking per-formance, and could result in an accident.W
Trailer Hitch ClassificationThe following chart provides the industry standard forthe maximum trailer weight agiven trailer hitch class cantow and sho
Trailer Towing Weights (Maximum Trailer Weight Ratings)The following chart provides the maximum trailer weight ratings towable for your given drivetra
Engine/Transmis-sionAxle Model GCWR (GrossCombined Wt.Rating)Frontal Area Max. GTW (GrossTrailer Wt.)Max. Tongue Wt.(See Note 1)3.8L/Automatic4.10 2 D
Engine/Transmis-sionAxle Model GCWR (GrossCombined Wt.Rating)Frontal Area Max. GTW (GrossTrailer Wt.)Max. Tongue Wt.(See Note 1)3.8L/Manual4.10 4 Door
NOTE: The trailer tongue weight must be considered aspart of the combined weight of occupants and cargo, andshould never exceed the weight referenced
Consider the following items when computing theweight on the rear axle of the vehicle:•The tongue weight of the trailer.•The weight of any other type
Window Lockout Switch (4 Door Models Only)The window lockout switch (located between the win-dow switches) allows you to disable the rear windowswitch
WARNING!Improper towing can lead to an injury accident.Follow these guidelines to make your trailer towingas safe as possible:Make certain that the lo
2. GTW3. GAWR4. Tongue weight rating for the trailer hitch utilized(This requirement may limit the ability to alwaysachieve the 10% to 15% range of to
actuated brakes. When towing a trailer equipped witha hydraulic surge actuated brake system, an electronicbrake controller is not required.−Trailer br
Towing Requirements — Trailer Lights & WiringWhenever you pull a trailer, regardless of the trailer size,stop lights and turn signals on the trail
Towing TipsBefore setting out on a trip, practice turning, stoppingand backing the trailer in an area away from heavytraffic.If using a manual transmi
The automatic transmission fluid and filter should bechanged if you REGULARLY tow a trailer for more than45 minutes of continuous operation. See “Sche
RECREATIONAL TOWING (BEHINDMOTORHOME, ETC.)CAUTION!Front or rear wheel lifts should not be used. Internaldamage to the transmission or transfer case w
4. Start engine.5. Shift automatic transmission into D (Drive) or manualtransmission into gear.6. Release brake pedal and ensure that there is no vehi
3. Shift automatic transmission into D (Drive) or releaseclutch on manual transmissions.NOTE: When shifting out of transfer case N (Neutral)on automat
WHAT TO DO IN EMERGENCIESCONTENTS䡵 Hazard Warning Flashers ...350䡵 If Your Engine Overheats ...351䡵 Jacking And Tire Chang
The swing gate can be unlocked using the remote keylessentry, or by activating the power door lock switcheslocated on the front doors.To open the swin
HAZARD WARNING FLASHERSYour vehicle’s hazard warning flasher is an emergencywarning system. When you activate it, all front and reardirectional signal
IF YOUR ENGINE OVERHEATSIn any of the following situations, you can reduce thepotential for overheating by taking the appropriate ac-tion.•On the high
JACKING AND TIRE CHANGINGWARNING!•Getting under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you.You could be crus
Spare Tire StowageTo remove the spare tire from the carrier, remove the tirecover, if equipped, and remove the lug nuts with the lugwrench turning the
Jacking Instructions1. Remove spare tire, jack and tools from stored location.2. Loosen (but do not remove) the wheel lug nuts byturning them to the l
WARNING!Raising the vehicle higher than necessary can makethe vehicle less stable and cause an accident. It couldslip off the jack and hurt someone ne
JUMP STARTINGIf the vehicle has a discharged battery, booster cables maybe used to obtain a start from a booster battery or thebattery in another vehi
WARNING!Do not permit vehicles to touch each other as thiscould establish a ground connection and personalinjury could result.5. Connect the other cab
6. Start the engine in the vehicle which has the boosterbattery, let the engine idle a few minutes, then start theengine in the vehicle with the disch
WARNING!Stand clear of vehicles when pulling with tow hooks.Tow straps and chains may break, causing seriousinjury.TOWING A DISABLED VEHICLEThe manufa
OCCUPANT RESTRAINTSSome of the most important safety features in yourvehicle are the restraint systems. These include the frontand rear seat belts for
MAINTAINING YOUR VEHICLECONTENTS䡵 Engine Compartment – 3.8L ...364䡵 Onboard Diagnostic System — OBD II ...365▫ Loose Fuel Filler Cap
▫ Driveline And Steering ComponentLubrication ...378▫ Body Lubrication ...378▫ Windshield Wiper Blades ...
䡵 Fluid Capacities ...412䡵 Fluids, Lubricants And Genuine Parts ...413▫ Engine ...413▫ Chassis ...
ENGINE COMPARTMENT – 3.8L364 MAINTAINING YOUR VEHICLE
ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor
Loose Fuel Filler Cap MessageAfter fuel is added, the vehicle diagnostic system candetermine if the fuel filler cap is possibly loose, improp-erly ins
Your vehicle has a simple ignition key actuated test,which you can use prior to going to the test station. Tocheck if your vehicle’s OBD system is rea
vehicle serviced before going to the I/M station. The I/Mstation canfail yourvehicle becausethe MILsymbol is onwith the engine running.REPLACEMENT PAR
MAINTENANCE PROCEDURESThe pages that follow contain the required maintenanceservices determined by the engineers who designed yourvehicle.Besides the
Research has shown that seat belts save lives, and thatthey can reduce the seriousness of injuries in a collision.Some of the worst injuries happen wh
CAUTION!Overfilling or underfilling the crankcase will causeaeration or loss of oil pressure. This could damageyour engine.Change Engine OilRoad condi
Engine Oil SelectionFor best performance and maximum protection for allengines under all types of operating conditions, themanufacturer recommends eng
present a problem to the environment. Contact yourauthorized dealer, service station, or governmentalagency for advice on how and where used oil can b
Spark PlugsSpark plugs must fire properly to assure engine perfor-mance and emission control. New plugs should be in-stalled at the mileage specified
WARNING!A hot exhaust system can start a fire if you park overmaterials that can burn. Such materials might begrass or leaves coming into contact with
Crankcase Emission Control SystemProper operation of this system depends on freedomfrom sticking or plugging due to deposits. As vehiclemileage builds
Maintenance-Free BatteryYour vehicle is equipped with a maintenance-free battery.You will never have to add water, nor is periodic main-tenance requir
include cleaning of the condenser fins and a performancetest. Drive belt tension should also be checked at thistime.WARNING!•Use only refrigerants and
WARNING!Fluid level should be checked on a level surface withthe engine off to prevent injury from moving parts,and to insure accurate fluid level rea
amount of a high quality lubricant such as Mopar威 LockCylinder Lubricant directly into the lock cylinder.Windshield Wiper BladesClean the rubber edges
WARNING!•Wearing a seat belt incorrectly is dangerous. Seatbelts are designed to go around the large bones ofyour body. These are the strongest parts
Exhaust SystemThe best protection against carbon monoxide entry intothe vehicle body is a properly maintained engine exhaustsystem.If younotice achang
garden hose vertically down the face of the A/C con-denser (if equipped) or the back of the radiator core.Check the engine cooling system hoses for br
CAUTION!•Mixing of antifreeze/coolant other than the speci-fied HOAT antifreeze/coolant may result in de-creased corrosion protection and engine damag
Use only high purity water such as distilled or deionizedwater when mixing the water/antifreeze (coolant) solu-tion. The use of lower quality water wi
children, do not store ethylene glycol based antifreeze/coolant in open containers or allow it to remain inpuddles on the ground. If ingested by a chi
coolant needs to be added, contents of coolant recov-ery bottle must also be protected against freezing.•If frequent antifreeze/coolant additions are
are present. Components should be replaced immedi-ately if there is any evidence of degradation that couldcause failure.Brake SystemIn order to assure
WARNING!Worn brake hoses can burst and cause brake failure.You could have an accident. If you see any signs ofcracking, scuffing, or worn spots, have
Use only brake fluid that has been in a tightly closedcontainer to avoid contamination from foreign matter. Donot allow petroleum base fluid to contam
Check the fluid level while the transmission is at normaloperating temperature 180° F (82° C). This occurs after atleast 15 mi (25 km) of driving. At
3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”Latch Plate Latch Plate To BuckleTHINGS TO KNOW
CAUTION!Be aware that if the fluid temperature is below 50° F(10° C), it may not register on the dipstick. Do not addfluid until the temperature is el
Fluid Level CheckCheck the fluid level by removing the fill plug. The fluidlevel should be between the bottom of the fill hole and apoint notmore than
Adding FluidFluid should be added only at filler hole until fluidbegins to run out of the hole.DrainFirst remove fill plug (B), then drain plug (C). R
Following off-road usage, completely inspect the under-body of your vehicle. Check tires, body structure, steer-ing, suspension and exhaust system for
hot or cold weather and other extreme conditions willhave an adverse effect on paint, metal trim, and under-body protection.The followingmaintenance r
CAUTION!Do not use abrasive or strong cleaning materials suchas steel wool or scouring powder, which will scratchmetal and painted surfaces.Special Ca
Wheel and Wheel Trim CareAll wheels and wheel trim, especially aluminum andchrome plated wheels should be cleaned regularly with amild soap and water
WARNING!Do not use volatile solvents for cleaning purposes.Many are potentially flammable, and if used inclosed areas they may cause respiratory harm.
Replace the belts if they appear frayed or worn or if thebuckles do not work properly.Appearance Care For Fabric Top ModelsCAUTION!To maintain the app
Care Of Fabric Top WindowsCAUTION!Your vehicle’s fabric top has pliable plastic windowswhich can be scratched unless special care is taken byfollowing
INTRODUCTIONThis is a specialized utility vehicle designed for bothon-road and off-road use. It can go places and performtasks for which conventional
WARNING!A belt that is buckled into the wrong buckle will notprotect you properly. The lap portion could ride too highon your body, possibly causing i
into the zipper teeth. If a stuck zipper slide is experi-enced, work the Mopar威 Soft Top Zipper Cleaner andLubricant into the zipper slide. Several ap
Cavity CartridgeFuseMiniFuseDescriptionJ1 40 AmpGreenPower Folding SeatJ2 30 AmpPinkTransfer Case/PwrLiftgate ModuleJ3 40 AmpGreenRear Door Module(RR
Cavity CartridgeFuseMiniFuseDescriptionJ18 20 AmpYellowPowertrain ControlModule (PCM) TransRangeJ19 60 AmpYellowRadiator FanJ20 30 AmpPinkFront Wiper
Cavity CartridgeFuseMiniFuseDescriptionM10 20 AmpYellowIgnition Off Draw —Vehicle EntertainmentSystem (IOD-VES),Satellite Digital AudioReceiver (SDARS
Cavity CartridgeFuseMiniFuseDescriptionM15 20 AmpYellowCOL MOD, IR SNS,Heater Ventilation,Air Conditioning/Automatic Tempera-ture Control (HVAC/ATC),
Cavity CartridgeFuseMiniFuseDescriptionM21 20 AmpYellowAuto Shut Down(ASD #3)M22 10 AmpRedRight Horn (RTHORN (HI/LOW)M23 10 AmpRedLeft Horn (LT HORN(H
Cavity CartridgeFuseMiniFuseDescriptionM32 10 AmpRedOccupant RestraintController (ORC), TTEUROPEM33 10 AmpRedNext Generation Con-troller (NGC), Global
CAUTION!•When installing the Integrated Power Modulecover, it is important to ensure the cover is prop-erly positioned and fully latched. Failure to d
REPLACEMENT BULBS — IF EQUIPPEDInterior Lights Bulb TypeAuto. Trans. Indicator Light ...658Courtesy Lights, Under Dash (1)...
BULB REPLACEMENTHead Light1. Open hood and support using prop rod.2. Remove the front grille. Turn the retainers along thetop 1/4 turn counter-clockwi
NOTE: The “Seat Belt Indicator Light” will remain onuntil the driver’s seat belt is buckled.WARNING!A lap belt worn too high can increase the risk ofi
Front Park/Turn Signal1. Remove the front grille. Turn the retainers along thetop 1/4 turn counter-clockwise and remove.2. Pull the bottom of the gril
Rear Tail, Stop, Turn Signal, and Back-Up Lights1. Remove the two (2) inboard screws attaching the taillight housing to the body. DO NOT REMOVE THEOUT
FLUID CAPACITIESU.S. MetricFuel (Approximate) — 2 Door Models 18.5 Gallons 70 LitersFuel (Approximate) — 4 Door Models 22.5 Gallons 85 LitersEngine Oi
FLUIDS, LUBRICANTS AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Form
ChassisComponent Fluid, Lubricant, or Genuine PartAutomatic Transmission Mopar威 ATF+4 Automatic Transmission FluidManual Transmission Mopar威 Manual Tr
MAINTENANCE SCHEDULESCONTENTS䡵 Emission Control System Maintenance ...416䡵 Maintenance Schedules ...416▫ Schedule “B” ...
EMISSION CONTROL SYSTEM MAINTENANCEThe “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified toassure t
•Trailer towing•Taxi, police, or delivery service (commercial service)•Off-road or desert drivingNOTE: If ANY of these apply to you then change youren
At Each Stop for Fuel•Check the engine oil level about 5 minutes after a fullywarmed engine is shut off. Checking the oillevel whilethe vehicle is on
Schedule “B”Follow this schedule if you usually operate your vehicleunder one or more of the following conditions.•Day or night temperatures are below
6. To release the belt, push the red button on the buckle.The belt will automatically retract to its stowed position.If necessary, slide the latch pla
Miles 3,000 6,000 9,000 12,000 15,000(Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000)Change the engine oil and engine oil filter, if notreplac
Miles 18,000 21,000 24,000 27,000 30,000(Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000)Change the engine oil and engine oil filter, if notre
Miles 33,000 36,000 39,000 42,000 45,000(Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000)Change the engine oil and engine oil filter, if notre
Miles 48,000 51,000 54,000 57,000 60,000(Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000)Change the engine oil and engine oil filter, if notr
Miles 48,000 51,000 54,000 57,000 60,000(Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000)Drain and refill the automatic transmission fluid.Re
Miles 63,000 66,000 69,000 72,000 75,000(Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000)Change the engine oil and engine oil filter, if
Miles 78,000 81,000 84,000 87,000 90,000(Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000)Change the engine oil and engine oil filter, if
Miles 93,000 96,000 99,000 102,000 105,000(Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000)Change the engine oil and engine oil filter, i
Miles 108,000 111,000 114,000 117,000 120,000(Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000)Change the engine oil and engine oil filter
Miles 123,000 126,000 129,000 132,000 135,000(Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000)Change the engine oil and engine oil filter
WARNING!The rear center lap/shoulder belt is equipped with alock-out feature to ensure that the rear seat back is inthe fully upright and locked posit
Miles 138,000 141,000 144,000 147,000 150,000(Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000)Change the engine oil and engine oil filter
Inspection and service should also be performed anytimea malfunction is observed or suspected. Retain all re-ceipts.† Applies only if vehicle is used
Schedule “A”Miles 6,000 12,000 18,000 24,000 30,000(Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000)[Months] [6] [12] [18] [24] [30]Change the
Miles 36,000 42,000 48,000 54, 000(Kilometers) (60 000) (70 000) (80 000) (90 000)[Months] [36] [42] [48] [54]Change the engine oil and engine oil fil
Miles 60,000 66,000 72,000 78,000(Kilometers) (100 000) (110 000) (120 000) (130 000)[Months] [60] [66] [72] [78]Change the engine oil and engine oil
Miles 84,000 90,000 96,000 102, 000(Kilometers) (140 000) (150 000) (160 000) (170 000)[Months] [84] [90] [96] [102]Change the engine oil and engine o
Miles 108,000 114,000 120,000 126,000(Kilometers) (180 000) (190 000) (200 000) (210 000)[Months] [108] [114] [120] [126]Change the engine oil and eng
Miles 132,000 138,000 144,000 150,000(Kilometers) (220 000) (230 000) (240 000) (250 000)[Months] [132] [138] [144] [150]Change the engine oil and eng
Inspection and service should also be performed anytimea malfunction is observed or suspected. Retain all re-ceipts.〫 This maintenance is recommended
IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 Suggestions For Obtaining Service For YourVehicle ...440▫ Prepare For The Appointm
WARNING!Position the shoulder belt height adjusters so that thebelt rests across the middle of your shoulder. Failureto adjust the safety belt properl
SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with
technicians, special tools, and the latest information toassure your vehicle is fixed correctly and in a timelymanner.This is why you should always ta
Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY)To assist customers who have hearing difficulties, themanufacturer has installed specia
WARNING!Engine exhaust, some of its constituents, and certainvehicle components contain or emit chemicalsknown to the State of California to cause can
To contact NHTSA, you may either call the Auto SafetyHotline toll free at 1–888–327–4236 (TTY: 1–800–424–9153), or go to http://www.safercar.gov; or w
•Diagnostic Procedure Manuals.Filled with diagrams, charts and detailed illustrations,these practical manuals make it easy for students andtechnicians
DEPARTMENT OF TRANSPORTATION UNIFORMTIRE QUALITY GRADESThe following describes the tire grading categories estab-lished by the National highway Traffi
Temperature GradesThe temperature grades are A (the highest), B, and C,representing the tire’s resistance to the generation of heatand its ability to
Enhanced Seat Belt Use Reminder System(BeltAlert)If the driver or front passenger seat belt has not beenbuckled within 60 seconds of starting the vehi
ABS (Anti-Lock Brake System) ...204,296Adding Fuel ...325Adding Washer Fluid ...194Air Cleaner, Eng
Battery ...376Emergency Starting ...356Keyless Transmitter Replacement (RKE) ...25Belts, Drive ...
Check Engine Light(Malfunction Indicator Light) ...208,366Child Restraint ...64,65,71,75Child Restraint Tether Anchors ...
Dimmer Switch, Headlight ...100DipsticksOil (Engine) ...369Disabled Vehicle Towing ...359Disarmin
Emission Control System Maintenance ...366,416EngineAir Cleaner ...375Block Heater ...269Break-In Reco
Turn Signal ...203,410,411Flooded Engine Starting ...266Fluid Capacities ...412Fluid Level Che
Odometer ...208Speedometer ...202Tachometer ...205Gear Ranges ...
Instrument Cluster ...201Instrument Panel and Controls ...200Instrument Panel Lens Cleaning ...397Integrated
Cruise ...205Daytime Running ...101Dimmer Switch, Headlight ...100Electronic Stability Progr
Lower Anchors and Tether for CHildren(LATCH) ...70,71Lubrication, Body ...378Maintenance Free Battery ...
4. Turn the ignition key to the OFF position. A singlechime will sound to signify that you have successfullycompleted the programming.The Enhanced War
Oil, Engine ...369Capacity ...412Dipstick ...369Filter ...
Radio, Navigation ...245Radio Operation ...252Radio, Satellite ...246,247Rear Axle (Diffe
Satellite Radio Antenna ...248Schedule, Maintenance ...416Seat Belt Reminder ...45Seat Belts ...
Shoulder Belt Upper Anchorage ...43Shoulder Belts ...37Side Airbag ...58Signals, Turn ...
Theft System Disarming ...19Tilt Steering Column ...103Tip Start ...266Tire and Loading
Traction Control ...108Traction Control Light ...208Trailer Towing ...330Cooling System
Viscosity, Engine Oil ...371Warning Flasher, Hazard ...350Warning Lights(Instrument Cluster Description) ...
INTRODUCTION INTRODUCTION Roll Over WarningHOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATION
WARNING!Using a seat belt extender when not needed canincrease the risk of injury in a collision. Only usewhen the seat belt is not long enough when i
This vehicle has airbags for both the driver and rightfront passenger as a supplement to the seat belt restraintsystems. The driver’s front airbag is
WARNING!• Do not put anything on or around the front airbag coversor attempt to manually open them. You may damage theairbags and you could be injured
Roll Over WarningUtility vehicles have a significantly higher roll over ratethan other types of vehicles. This vehicle has a higherground clearance, h
severe side collisions. In certain types of collisions, boththe front and side airbags may be triggered. But even incollisions where the airbags work,
3. The driver and front passenger seats should be movedback as far as practical to allow the front airbags room toinflate.4. If your vehicle hasside a
Airbag System ComponentsThe airbag system consists of the following:•Occupant Restraint Control Module•Airbag Warning Light•Driver Airbag•Passenger Ai
The ORC also monitors the readiness of the electronicparts of the system whenever the ignition switch is inthe START or ON positions. These include al
•The Occupant Classification System (OCS) is part ofa Federally regulated safety system required for thisvehicle. It is designed to turn off the front
The “PAD Indicator Light” should not be illuminatedwhen teenagers, most children in a forward-facingchild restraint or booster seats, most children th
The OCS classifies an occupant using weight sensorsmounted in the base of the front passenger seat. Anyweight on the seat will be sensed by the system
both the “PAD Indicator Light” and the “Airbag WarningLight” are illuminated to show that the passenger airbagis turned off until the fault is cleared
•Your vehicle has four Weight Sensors located betweenthe seatand the floor pan. The weight sensorsmeasureapplied weight and transfers that information
The following requirements must be strictly adhered to:•Do not modify the front passenger seat assembly orcomponents in any way.•Do not modify the fro
Failure to use driver and passenger seat belts providedis a major cause of severe or fatal injury. In fact, the U.S.government notes that the universa
If A Deployment OccursThe airbag system is designed to deploy when theOccupant Restraint Control (ORC) Module detects amoderate-to-severe frontal coll
WARNING!Deployed airbags and seat belt pretensioners cannotprotect you in another collision. Have the airbags,seat belt pretensioner, and seat belt re
NOTE:Perchlorate Material – special handling may apply,See www.dtsc.ca.gov/hazardouswaste/perchlorateAirbag Warning LightYou will want to have the air
DaimlerChrysler Corporation, such investigations maybe requested by customers, insurance carriers, govern-ment officials, and professional crash resea
•Airbag disable lamp status (if equipped)•⬙Time⬙ of airbag deployment (in terms of ignitioncycles and vehicle mileage)•Airbag deployment level (if app
WARNING!In a collision, an unrestrained child, even a tiny baby,can become a missile inside the vehicle. The forcerequired to hold even an infant on y
WARNING!•Improper installation can lead to failure of aninfant or child restraint. It could come loose in acollision. The child could be badly injured
extracted from the retractor. Allow the belt to return tothe retractor, pulling on the excess webbing to tightenthe lap portion about the child restra
vehicle by the lap/shoulder belt or the LATCH childrestraint anchorage system (Refer to LATCH — ChildSeat Anchorage System in this section.)The belt-p
NOTE: To reset this feature you must let all of the beltwebbing return into the retractor. You will not be able topull out more webbing until all of t
NOTE: After you read the manual, it should be storedin the vehicle for convenient reference and remain withthe vehicle when sold so that the new owner
LATCH — Child Seat Anchorage System (LowerAnchors and Tether for CH ildren)Your vehicle’s rear seat is equipped with the childrestraint anchorage syst
The rear seating positions have lower anchorages that arecapable of accommodating LATCH-compatible childseats having flexible, webbing-mounted lower a
The rear seat lower anchorages are round bars,located at the rear of the seat cushion where itmeets the seat back, and are visible when youlean into t
In addition, thereare tetherstrap anchoragesbehind eachrear seating position located on the back of the seat.Latch Anchorages (4 Door Models)Tether St
Many, but not all restraint systems will be equipped withseparate straps on each side, with each having a hook orconnector for attachment to the lower
WARNING!Improper installation of a child restraint to theLATCH anchorages can lead to failure of an infant orchild restraint. The child could be badly
to do something more. Disconnect the latch plate fromthe buckle, turn the buckle around, and insert the latchplate into the buckle again. If you still
WARNING!An incorrectly anchored tether strap could lead toincreased head motion and possible injury to thechild. Use only the anchor positions directl
A new engine may consume some oil during its first fewthousand miles (kilometers) of operation. This should beconsidered as a normal part of the break
•On hardtop models, keep the tailgate window closedwhen driving your vehicle. On fabric top models, donot drive with the rear window curtain up unless
8 INTRODUCTION
Safety Checks You Should Make Outside TheVehicleTiresExamine tires for excessive tread wear or uneven wearpatterns. Check for stones, nails, glass, or
UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 Mirrors ...85▫ Inside Day/Night Mirror ...85▫ Outside Mi
䡵 Lights ...97▫ Interior Lights ...97▫ Multi-Function Control Lever ...98▫ Parking Lights
䡵 Electronic Brake Control System ...107▫ ABS (Anti-Lock Brake System) ...107▫ TCS (Traction Control System) ...108▫ BAS (B
▫ Door Frame Removal (4 Door Models) ...135▫ Door Frame Installation (4 Door Models) ...138䡵 Soft Top (2 Door Models) ...141▫ Foldin
MIRRORSInside Day/Night MirrorThe mirror should be adjusted to center on the viewthrough the rear window. A two-point pivot systemallows for horizonta
Outside MirrorsTo receive maximum benefit, adjust the outside mirror(s)to center on the adjacent lane of traffic with a slightoverlap of the view obta
SEATSWARNING!Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt m
Manual Seat Height Adjustment — If EquippedThe driver’s seat height can be raised or lowered, byusing the ratcheting handle on the outboard side of th
2. Lift the handle to return the seatback to an uprightposition.Front Passenger Easy Entry Seat (2 Door Models)Push the lever on the seatback rearward
WARNINGS AND CAUTIONSThis manual contains WARNINGS against operatingprocedures, which could result in an accident or bodilyinjury. It also contains CA
Head RestraintsHead restraints can reduce the risk of whiplash injury inthe event of impact from the rear. Adjustable headrestraints should be adjuste
Also, be sure that the front seats are fully upright andpositioned forward. This will allow the rear seat to folddown easily.1. Lift the seatback rele
Removing the Rear Seat (2 Door Models)WARNING!•It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision people
4. Press down on release bar on each side, and pull seatout and away from lower bracket.5. Remove seat from the vehicle.Replacing the Rear Seat (2 Doo
NOTE: Prior tofolding therearseat, itmay benecessaryto reposition the front seat to it’s mid-track position.Also, be sure that the front seats are ful
NOTE: When lifting up on the release handle, theseatback will release easier if you do not pull forward onthe seatback; only lift up on the release ha
TO OPEN AND CLOSE THE HOODTo open hood, first release both hood latches.Next, locate handle in middle of the front end of thehood. Insert hand into ga
LIGHTSInterior LightsThe overhead light comes on when a door is opened. Itmay also be turned on by rotating the control for thedimmer switch on the mu
When a door is open and the interior lights are on,rotating the dimmer control all the way down to the OFFdetent will cause all the interior lights to
Parking Lights, Instrument Panel Lights, andHeadlightsTurn the end of the multi-function control lever to thefirst detent for parking lights and instr
Comments to this Manuals