Jeep 2006 Commander User Manual

TABLE OF CONTENTSSECTION PAGE1INTRODUCTION...32THINGS TO KNOW BEFORE STARTING YOUR VEHICLE..

Things You Should Know About Your UConnect™SystemVoice Recognition (VR)•Always wait for the beep before speaking.•Speak normally, without pausing, jus

•You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must bespoken ⬙eight-zero-zero.⬙•Even though international dialing for most numbercombinations is

102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1033

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

North American EnglishPrimary Alternate(s)Zero OhAdd location Add newAll All of themConfirmation prompts Confirmations promptsDelete a name DeleteLang

Front Seat Adjustment — ReclineTo adjust the seatback, lift the lever located on theoutboard side of the seat, lean back, and release the leverat the

Head RestraintsHead restraints can reduce the risk of whiplash injury inthe event of impact from the rear. Adjustable headrestraints should be adjuste

8 - Way Driver’s Power SeatThe driver’s power seat switches are located on theoutboard side of the driver’s seat lower side trim. Thebottom switch con

indicate the level of heat in use. Two LEDs are illumi-nated for high, one for low, and none for off. Pressing theswitch once will select high-level h

THINGS TO KNOW BEFORE STARTING YOUR VEHICLECONTENTS䡵 A Word About Your Keys ...14▫ Ignition Key ...14▫ Key-In-Ig

1. Pull up on the seatback lever located on the outboardside of the seat.NOTE: Also, pulling upward on this handle allows theoutboard seating position

NOTE: If sitting in the third row seat, pull rearward onthe release strap located at the rear of the seat and tumblethe seat forward.Fold and Tumble S

Folding Middle Seatback (Second Row Seat)1. Pull the release strap.2. Lower the center seatback.Center Seat Armrest (Second Row Seat) — IfEquippedThe

50/50 Third Row Folding SeatTo Lower Rear SeatEither side of the third row seat can be lowered to allowfor extended cargo space, and still maintain so

To Raise Rear Seat1. Open the tailgate.2. Detach pull strap from back of seat, and pull seatbackupward until it locks into place. Reattach strap.3. Ra

Your vehicle may have been delivered with two RemoteKeyless Entry transmitters. One or both transmitters canbe linked to either memory position. The m

5. Turn on the radio and set the radio station presets (upto 10 AM and 10 FM stations can be set).6. Turn the ignition switch to the OFF position andr

To recall the memory settings for driver one, pressmemory button number 1 on the driver’s door or the“Unlock” button on the Remote Keyless Entry trans

NOTE: Once programmed, all transmitters linked tomemory can be easily enabled or disabled at one time.Refer to Remote Linked to Memory under ⬙Electron

NOTE: The Easy Entry Easy Exit feature is not enabledwhen the vehicle is delivered from the factory. The EasyEntry Easy Exit feature is enabled (or la

▫ Transmitter Battery Service ...24䡵 Security Alarm System — If Equipped ...25▫ ToSetTheAlarm ...26▫ To Disarm Th

Then, reach under the hood, move safety latch to the left,and lift the hood. To prevent possible damage, do notslam the hood to close it. Use a firm d

Courtesy/Reading LightsEach light can be turned on by pressing the recessed areaof the lens. To turn these lights off, press the recessed areaof the l

Multi-Function Control LeverThe multi-function control lever controls the operation ofthe headlights, turn signals, headlight beam selection,instrumen

Automatic Headlight System — If EquippedTurn the end of the multi-function control lever to thethird detent to activate the automatic headlight system

NOTE: When your headlights come on during thedaytime, the instrument panel lights will automaticallydim to the lower nighttime intensity. Refer to “In

headlights to remain on longer (closer to the vehicle).Also, dirt, film, and other obstructions (sticker, toll box,etc.) on the windshield or camera l

Fog Lights — If EquippedThe fog light switch is located in the multi-function control lever. To activate the fog lights,turn on the park/turn lights,

Headlight Time DelayThere is also a feature that delays turning off the vehiclelights for 30, 60, or 90 seconds after the ignition switch isturned OFF

To use the washer, pull the lever toward you and holdwhile spray is desired. If the lever is pulled while in thedelay range, the wiper will operate fo

Rain Sensing Wipers—If EquippedThis feature senses moisture on the windshield andautomatically activates the wipers for the driver. Thefeature is espe

䡵 Safety Tips ...69▫ Exhaust Gas ...69▫ Safety Checks You Should Make Inside TheVehicle...

driver desires more sensitivity. Place the wiper switch inthe OFF position when not using the system.NOTE:•The rain sensing feature will not operate w

TILT STEERING COLUMNTo tilt the column, push down on the lever below the turnsignal control and move the wheel up or down, asdesired. Pull the lever b

ABS (Anti-Lock Brake System)This system aids the driver in maintaining vehicle controlunder adverse braking conditions. The system controlshydraulic b

TCS (Traction Control System)This system monitors the amount of wheel spin of each ofthe driven wheels. If wheel spin is detected, brakepressure is ap

WARNING!BAS (Brake Assist System) cannot prevent the natu-ral laws of physics from acting on the vehicle, norcan it increase the traction afforded by

NOTE: Anytime the ESP system is in the “Full Off”mode, ERM is disabled. Refer to ESP (Electronic StabilityProgram) for a complete explanation of the a

•Understeer - when the vehicle is turning less thanappropriate for the steering wheel position.The ⬙ESP/TCS Indicator Light⬙ located in the instrument

High Range (4WD Models) or 2WD ModelsOnThis is the normal operating mode for ESP in 4WD highrange and in 2WD vehicles. Whenever the vehicle isstarted

NOTE: To improve the vehicle’s traction when drivingwith snow chains, or starting off in deep snow, sand, orgravel, it may be desirable to switch to t

WARNING!With the ESP switched off, the enhanced vehiclestability offered by ESP and ERM are unavailable. Inan emergency evasive maneuver, the ESP and

A WORD ABOUT YOUR KEYSThe keys for your new vehicle are enclosed in a plasticbag with the key code number on it. If you received yourkeys without the

Electronic Vehicle Information Center (EVIC). Refer to“Electronic Vehicle Information Center (EVIC)” in Sec-tion 4 of this manual. (See page 186 for m

If the “ESP/BAS Warning Lamp” comes oncontinuously with the engine running, a mal-function has been detected in either the ESP orthe BAS system, or bo

Rear Park Assist SensorsThe four Rear Park Assist Sensors, located in the rearfascia, monitor the area behind the vehicle that is withinthe sensors’ f

When the obstacle is detected at a distance of about 59inches (150 cm) from the rear fascia, the outermost LEDsof the warning display will be ON with

Enable/Disable the Rear Park Assist SystemThe Rear Park Assist System can be enabled and disabledwith a switch located in the switch bank of the instr

Service the Rear Park Assist SystemWhen the Rear Park Assist System is defective, theinstrument cluster will actuate a single chime, once perignition

WARNING!• Drivers must be careful when backing up even whenusing the Rear Park Assist System. Always checkcarefully behind your vehicle, look behind y

ADJUSTABLE PEDALS — IF EQUIPPEDThis feature allows both the brake and accelerator pedalsto move toward the driver to provide improved positionwith the

•The pedals can be adjusted while driving.•The pedals cannot be adjusted when the vehicle is in R(Reverse) or when the Speed Control is ON. A messagew

To ActivatePress the ON·OFF button to turn the system ON. To turnthe system OFF, press the ON·OFF button again. Thesystem should be turned OFF when no

Key-In-Ignition ReminderIf the driver’s door is opened when the key is in theignition and not turned to the ON position, a chime willsound to remind y

To Vary the Speed SettingWhen the Speed Control is ON, speed can be increasedby pressing and holding the RES·ACCEL button. Whenthe button is released,

WARNING!Leaving the Speed Control ON when not in use isdangerous. You could accidentally set the system orcause it to go faster than you want. You cou

OVERHEAD CONSOLE — IF EQUIPPEDThe overhead console contains an optional universalgarage door opener (HomeLink威), storage for sunglasses,and optional p

WARNING!A moving garage door can cause injury to people andpets in the path of the door. People or pets could beseriously or fatally injured. Only use

Programming HomeLinkNOTE: When programming a garage door opener, it isadvised to park outside the garage. It is also recom-mended that a new battery b

2. Position the end of your hand-held transmitter 1-3inches (3-8 cm) away from the HomeLink buttons.3. Simultaneously press and hold both the HomeLink

NOTE: To program the remaining two HomeLink but-tons, begin with ⬙Programming⬙ step two. Do not repeatstep one.NOTE: If your hand-held transmitter app

Canadian Programming/Gate ProgrammingCanadian radio-frequency laws require transmitter sig-nals to ⬙time-out⬙ (or quit) after several seconds oftransm

•Press and hold the two outer HomeLink buttons andrelease only when the EVIC display shows “CHAN-NELS CLEARED” (after 20 seconds). Release bothbuttons

HomeLink威 is a trademark owned by Johnson Controls,Inc.POWER SUNROOF — IF EQUIPPEDThe power sunroof switch is located on the overheadconsole.WARNING!•

If the SKIM indicator light comes on during normalvehicle operation (it has been running for longer than 10seconds) a fault has been detected in the e

Opening Sunroof - ExpressPress the switch rearward and release, and the sunroofwill open automatically from any position. The sunroofwill open fully,

Sunshade OperationThe sunshade can be opened manually. However, thesunshade will open automatically as the sunroof opens.NOTE: The sunshade cannot be

NOTE: Hold onto shade handle until shade is com-pletely open or closed.POWER OUTLETTo the right of the convenience tray (lower center ofinstrument pan

The rear power outlet (if equipped) is located in the leftrear cargo area.The power outlets are a direct feed from the battery sothey receive power wh

CAUTION!Electrical Outlet Use With Engine Off•Many accessories that can be plugged in drawpower from the vehicle’s battery, even when notin use (i.e.,

NOTE: The cup holder insert is removable, from theconsole, for cleaning. It can be reinstalled with the largercup depression towards the passenger sea

Cup Holders (Third Row Seat)The third row seat passengers have cup holders on theleft and right rear trim panels.CARGO AREA FEATURESCargo Load FloorTh

NOTE: The cargo load floor latches should not beused as cargo tie-downs.1. Flip up pull loop(s) so they are perpendicular (straightup) to the top surf

5. Push loop(s) back down, so they are parallel to the topof the tray.REAR WINDOW FEATURESRear Window Wiper/WasherA switch on the right side of the st

the rear wiper switch or the ignition switch needs to beturned OFF and ON to restart the rear wiper.Adding Washer FluidThe fluid reservoir for the win

consists of programming a blank key to the vehicleelectronics. A blank key is one which has never beenprogrammed.NOTE: When having the Sentry Key Syst

NOTE: If the rear cross rail (or any metallic object) isplaced over the satellite radio antenna (if equipped), youmay experience interruption of satel

WARNING!Cargo must be securely tied before driving yourvehicle. Improperly secured loads can fly off thevehicle, particularly at high speeds, resultin

UNDERSTANDING YOUR INSTRUMENT PANELCONTENTS䡵 Instrument Panel And Interior Controls ...176䡵 Instrument Cluster ...177䡵 Instrume

▫ Operation Instructions -(CD Mode For CD Audio Play) ...206▫ Load/Eject Button(CD Mode For CD Audio Play) ...208▫ Notes On Playing MP

▫ Selecting Satellite Mode In REF Radios ...227▫ Selecting Satellite Mode In RAQ Radios ...227▫ Selecting a Channel ...228▫ Stor

INSTRUMENT PANEL AND INTERIOR CONTROLS176 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTERUNDERSTANDING YOUR INSTRUMENT PANEL 1774

INSTRUMENT CLUSTER DESCRIPTION1. SpeedometerIndicates vehicle speed.2. Brake Warning LightThe BRAKE warning light will come on whenthe ignition is fir

engine start. If the bulb does not come on when turningthe key from OFF to ON, have the condition checkedpromptly.Certain conditions such as a loose o

2. This device must accept any interference that may bereceived, including interference that may cause undes-ired operation.ILLUMINATED ENTRYThe inter

If the ABS light is on, the brake system should be servicedas soon as possible to restore the benefits of Anti-Lockbrakes. If the ABS light does not t

prevailing road conditions. The “ESP/TCS IndicatorLight” will flash any time the ESP or TCS is active andhelping to improve vehicle stability. If the

13. Temperature GaugeThe temperature gauge shows engine coolant tempera-ture. Any reading within the normal range indicates thatthe engine cooling sys

14. Electronic Vehicle Information Center DisplayWhen the appropriate conditions exist, this displayshows the Electronic Vehicle Information Center (E

or remain on continuously. Refer to ⬙Enhanced DriverSeat Belt Reminder System (BeltAlert)⬙ in the OccupantRestraints section for more information.19.

when the engine is running, immediate service is re-quired and you may experience reduced performance, anelevated/rough idle or engine stall and your

ELECTRONIC VEHICLE INFORMATION CENTER— IF EQUIPPEDThe electronic vehicle information center (EVIC) locatedin the instrument cluster, when the appropri

•LIFTGATE/DOOR OPEN (with graphic)•LIFTGATE/DOORS OPEN (with graphic)•LIFTGLASS OPEN (with graphic)•HOOD OPEN (with graphic)•HOOD/DOOR OPEN (with grap

•CHECK GAS CAP•ESP OFF•MEMORY #1 POSITIONS SET•MEMORY #2 POSITIONS SET•MEMORY SYSTEM DISABLED — SEATBELT FAS-TENED (with graphic)•MEMORY SYSTEM DISABL

Customer Programmable FeaturesPress the MENU button until one of the display choicesfollowing appears:Language?When in this display you may select one

CAUTION!An unlocked vehicle is an invitation to thieves.Always remove the key from the ignition and lockall of the doors when leaving the vehicle unat

Display U.S. or Metric?Pressing the STEP button when in this display selects USor Metric. The overhead console and instrument paneldisplays will be in

memory set position using the door mounted switch.Pressing the STEP button when in this display will select“Yes” or “No.”Sound Horn With Lock?When thi

this display will select “Low Beam” or “Low/HighBeam.” Refer to “Lights — SmartBeams” in Section 3 ofthis manual.NOTE: System will activate at or abov

Easy Entry/Exit Seat? (Available with Memory SeatOnly)This feature provides automatic driver’s seat positioningwhich will enhance driver mobility out

WARNING!Even if the display still reads a few degrees above32°F ( 0°C), the road surface may be icy, particularlyin woods or on bridges. Drive careful

Trip ComputerThis feature, located in the instrument cluster, displaysthe following information when the display is in the“Compass/Temperature” mode a

Reset ButtonPress the RESET button to reset the display you are in.Press and hold the RESET button (for 2 seconds) to resetall of the displays.Average

Elapsed TimeShows the accumulated ignition ON time since the lastreset.Tire Pressure Display — If EquippedShows the current pressure of all 4 road tir

NOTE: To ensure proper compass calibration, makesure the compass variance is properly set before manu-ally calibrating the compass. Refer to Variance

To set the variance: Turn the ignition ON and set thedisplay to “Compass/Temperature.” Press the C/T but-ton for approximately 5 seconds. The last var

Power Door LocksA door lock switch is on each front door panel. Press thisswitch to lock or unlock the doors.If the plunger is down when the door is c

Two Types of SignalsThere are two basic types of radio signals... AM orAmplitude Modulation, in which the transmitted soundcauses the amplitude, or he

Operating Instructions - Radio ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.Power Switch/Volume Control (Rotary

SEEK Button (Radio Mode)Press and release the SEEK button to search for the nextlistenable station in either AM/FM or Satellite (ifequipped) mode. Pre

2. Adjust the hours by turning the right side Tune /Audio control.3. After the hours are adjusted, press the right side Tune/ Audio control to set the

Press the rotary TUNE control a fifth time and FADE willdisplay. Turn the TUNE control to the left or right toadjust the sound level between the front

Nostalgia NostalgiaOldies OldiesPersonality PersonalityPublic PublicRhythm and Blues Rhythm_and_BluesReligious Music Religious_MusicReligious Talk Rel

You may add a second station to each push-button byrepeating the above procedure with this exception: Pressthe SET/DIR button twice and SET 2 will sho

CAUTION!This CD player will accept 4 3/4 inch (12 cm) discsonly. The use of other sized discs may damage theCD player mechanism.You may eject a disc w

LOAD/EJECT Button (CD Mode for CD AudioPlay)LOAD/ EJECT - LoadPress the LOAD/ EJECT button and the push-button with the corresponding number wherethe

TIME Button (CD MODE for CD Audio Play)Press this button to change the display from a large CDplaying time display to a small CD playing time display.

Automatic Unlock on Exit Feature — OnlyAvailable if Auto Lock is EnabledThis feature will unlock all the doors when the driver’sdoor is opened if the

Notes On Playing MP3 FilesThe radio can play MP3 files, however, acceptable MP3file recording media and formats are limited. Whenwriting MP3 files, pa

Supported MP3 File FormatsThe radio will recognize only files with the *.mp3 exten-sion as MP3 files. Non-MP3 files named with the *.mp3extension may

Playback of MP3 FilesWhen a medium containing MP3 data is loaded, theradio checks all files on the medium. If the mediumcontains a lot of folders or f

LOAD / EJECT - EjectPress the LOAD/ EJECT button and the push-button with the corresponding number wherethe CD was loaded and the disc will unloadand

AM/FM Button (CD Mode for MP3 Play)Switches back to Radio mode.RND/ PTY Button (CD Mode for MP3 Play)Pressing this button plays files randomly.SET/DIR

Operating Instructions - Radio ModeNOTE: The ignition switch must be in the ON or ACCposition to operate the radio.Power Switch/Volume Control (Rotary

SEEK Button (Radio Mode)Press and release the SEEK button to search for the nextlistenable station in either AM/FM or Satellite (ifequipped) mode. Pre

2. Adjust the hours by turning the right side Tune/Audio control.3. After the hours are adjusted, press the right sideTune/Audio control to set the mi

Press the rotary TUNE control a fifth time and FADE willbe displayed. Turn the TUNE control to the left or right toadjust the sound level between the

Inserting The Compact Disc (Single CD Player)Gently insert one CD into the CD player with the CDlabel facing up. The CD will automatically be pulled i

NOTE: If desired, the system can be programmed tounlock all doors on the first press of the “Unlock” button.Refer to “Remote Unlock Driver’s Door 1st”

EJECT Button (CD Mode)Press this button and the disc will unload andmove to the entrance for easy removal. Theunit will switch to the last selected mo

Operation Instructions - Auxiliary ModeThe auxiliary (AUX) jack is an audio input jack, whichallows the user to plug in a portable device such as anMP

TIME Button (Auxiliary Mode)Press this button to change the display from elapsedplaying time to time of day. The time of day will bedisplayed for 5 se

Satellite Navigation Radio with CD Player with MP3Capability (REC) - combines a Global-PositioningSystem-based navigation system with an integrated co

VIDEO ENTERTAINMENT SYSTEM (SALES CODEXRV) — IF EQUIPPEDThe optional VES™ (Video Entertainment System) con-sists of a DVD player and LCD (liquid cryst

The LCD screen is located on the headliner behind thefront seats.Lowering the Display ScreenRemote Control LocationUNDERSTANDING YOUR INSTRUMENT PANEL

SATELLITE RADIO — IF EQUIPPEDSatellite radio uses direct satellite to receiver broadcast-ing technology to provide clear digital sound, coast tocoast.

first four digits are displayed. The radio will exit theESN/SID mode when any other button is pushed, theignition is turned OFF, or 5 minutes has pass

Selecting a ChannelPress and release the SEEK or TUNE buttons to search forthe next channel. Press the top of the button to search upand the bottom of

NOTE: Pressing the ⬙SEEK⬙ or ⬙SCAN⬙ button whileperforming a music type scan will change the channel byone and stop the search. Pressing a pre-set mem

WARNING!Driving with the flipper glass open can allow poi-sonous exhaust gases into your vehicle. You and yourpassengers could be injured by these fum

REMOTE SOUND SYSTEM CONTROLS — IFEQUIPPEDThe remote sound system controls are located on the rearsurface of the steering wheel. Reach behind the wheel

The button located in the center of the left hand controlwill tune to the next preset station that you have pro-grammed in the radio preset push-butto

RADIO OPERATION AND CELLULAR PHONESUnder certain conditions, the cellular phone being On inyour vehicle can cause erratic or noisy performance fromyou

Press this button to turn on and off the air condi-tioning. Cool dehumidified air comes through theoutlets selected by the mode selector. Press thebut

Temperature ControlThe temperature of air can be selectedby rotating the center temperaturecontrol knob. The coldest temperaturesetting is on the extr

Bi-LevelAir flows both through the outlets located in theinstrument panel and those located on the floor. Airflows through the registers in the back o

Operating Tips236 UNDERSTANDING YOUR INSTRUMENT PANEL

Automatic Temperature Control — If EquippedThe Infrared Dual-Zone Climate Control System auto-matically maintains the interior comfort level desired b

LO AUTO position should be used for front seat occu-pants only. The HI AUTO position should be used whenmore air flow is desired, or when rear seat oc

NOTE:•The surface of the climate control panel, and the topcenter of the instrument panel should be kept free ofdebris due to the climate control sens

2. While the “Unlock” button is pressed, (after 4 seconds)press the “Lock” button. Release both buttons.The “Flash Lights On Lock/Unlock” feature can

240 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Regardless of the type of operation, when atemperature knob is set to the full clockwise or fullcounterclockwise position, the system will deliv

Air flows through the registers in the back of thecenter console, and under the front seats to the rearseat passengers. These registers can be closed

This button can be used to block out smoke,odors, dust, high humidity, or if rapid coolingis desired. The recirculation mode should onlybe used tempor

Rear Mode ControlIf rear heating/cooling is desired, press the “Rear On/OffSwitch” (located in the upper switch bank above thecontrols) and select “Fl

•Bi-LevelAir flows through both the outlets located in therear quarter trim panels, and the one located onthe floor. The rear quarter trim panel outle

•When the temperature knob is in the cold (Blue)position, cold air will be delivered from the outlets. Asthe temperature knob is turned towards the ho

Window FoggingInterior fogging on the windshield can be quickly re-moved by turning the mode selector to Defrost, andturning on the high blower. The D

STARTING AND OPERATINGCONTENTS䡵 Starting Procedures ...253▫ Normal Starting ...253▫ Extreme Cold Weather (Below –

2. Remove and replace the battery. Avoid touching thenew battery with your fingers. Skin oils may causebattery deterioration. If you touch a battery,

䡵 Anti-Lock Brake System ...271䡵 Power Steering ...274䡵 On-Road Driving Tips ...275䡵 Off-Road Driv

䡵 Tire Pressure Monitor System (TPMS) ...297▫ Base System ...297▫ Premium System ...299▫ General Informa

▫ Towing – 2WD Models ...323▫ Towing — Quadra-Trac I(Single-Speed Transfer Case) 4WD Models ...323▫ Towing — Quadra–Trac II /Quadra–Dri

STARTING PROCEDURESBefore starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belts.WARNING!Do not le

WARNING!Never pour fuel or other flammable liquids into thethrottle body air inlet opening in an attempt to startthe vehicle. This could result in a f

After StartingThe idle speed will automatically decrease as the enginewarms up.CAUTION!Long periods of engine idling, especially at highengine speeds

TRANSMISSION SHIFTING5–Speed Automatic TransmissionThe electronically controlled transmission provides aprecise shift schedule. The transmission elect

WARNING!It is dangerous to shift the selector lever out of P(Park) or N (Neutral) if the engine speed is higherthan idle speed. If your foot is not fi

WARNING!Unintended movement of a vehicle could injurethose in and near the vehicle. As with all vehicles,you should never exit a vehicle while the eng

shifter is in the D (Drive) position, allowing the selectionof the desired top gear. For example, if the driver shiftsthe transmission into 3 (third g

To Set the AlarmThe alarm will set when you use the remote keyless entrytransmitter to lock the doors and liftgate or when you usethe power door lock

NOTE: If the vehicle is started in extremely cold tem-peratures, the transmission may not shift into Overdriveand will automatically select the most d

overheating or failure due to excessive shifting. Whenoperating in “TOW/HAUL” mode, the transmission willshift to 3rd gear and 4th will be enabled und

4. Wait approximately 10 seconds, then restart the en-gine.5. Move the shift lever to the desired gear range.If the problem is no longer detected, the

cause damage to the transmission. The torque converterwill refill within five seconds of shifting from Park intoany other gear position.Rocking the Ve

FOUR-WHEEL DRIVE OPERATIONQuadra-Trac I姞 OperatingInstructions/Precautions — If EquippedThe Quadra-Trac I威 is a single speed (HI range only)transfer c

road surfaces only. Driving in the 4 LOW position on dryhard surfaced roads may cause increased tire wear anddamage to driveline components.When opera

N (Neutral)Neutral — Disengages both the front and rear driveshaftsfrom the powertrain. To be used for flat towing behindanother vehicle. Refer to “Re

4LOWto4HIWith the vehicle at speeds of 0 to 3 mph (0 to 5 km/h),key ON or engine running, shift the transmission into N(Neutral), and raise the transf

Neutral (N) Shift Procedure1. Key ON, engine off.2. Vehicle stopped, with foot on brake.3. Place transmission in N (Neutral).4. Hold down N (Neutral)

NOTE: If shift conditions/interlocks are not met, a“CHECK SHIFT PROCEDURES” message will flash fromthe EVIC (Electronic Vehicle Information Center). R

LIFTGATETo open the liftgate, pull up (squeeze) on the handle andlift. Manually unlocking the vehicle doors with theplunger or a key in the lock cylin

NOTE: The instrument cluster “Brake Warning Light”indicates only that the parking brake is applied. It doesnot indicate the degree of brake applicatio

WARNING!•Leaving children unattended in a vehicle is dan-gerous for a number of reasons. A child or otherscould be injured. Children should be warned

WARNING!Significant over or under inflation of tires, or mixingsizes of tires or wheels on the vehicle can lead to lossof braking effectiveness.The An

WARNING!•The Anti-Lock Brake System (ABS) cannot pre-vent the natural laws of physics from acting on thevehicle, nor can it increase braking or steeri

•Do not “ride” the brakes by resting your foot on thepedal. This could overheat the brakes and result inunpredictable braking action, longer stopping

NOTE: Increased noise levels at the end of the steeringwheel travel are considered normal and does not indicatethat there is a problem with the power

conventional 2-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfactorily inoff-road conditions. If at all possib

caution and maintain a steady controlled speed less than5 mph (8 km/h) in deep water to minimize wave effects.Flowing WaterIf the water is swift flowi

Hill ClimbingNOTE: Before attempting to climb a hill, determine theconditions at the crest and/or on the other side.Before climbing a steep hill, shif

Traction DownhillShift the transmission into a low gear and the transfercase to 4WD LOW range. Let the vehicle go slowly downthe hill with all four wh

Liftgate Flipper GlassThe liftgate flipper glass is also unlocked when theliftgate is unlocked. To open the flipper glass, push up onthe window switch

WARNING!Abrasive material in any part of the brakes maycause excessive wear or unpredictable braking. Youmight not have full braking power when you ne

TIRE SAFETY INFORMATIONTire MarkingsNOTE:•P (Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” molded

Tire Sizing ChartEXAMPLE:Size Designation:P = Passenger car tire size based on U.S. design standardsⴖ...blank...ⴖ = Passenger car tire based on Euro

EXAMPLE:Service Description:95 = Load Index—A numerical code associated with the maximum load a tire can carry.H = Speed Symbol—A symbol indicating th

Tire Identification Number (TIN)The TIN may be found on one or both sides of the tirehowever the date code may only be on one side. Tireswith white si

Tire Loading and Tire PressureTire Placard LocationNOTE: The proper cold tire inflation pressure is listedon either the face of the driver’s door or t

3) the tire size designed for your vehicle4) the cold tire inflation pressures for the front, rearand spare tires.LoadingThe vehicle maximum load on t

4. The resulting figure equals the available amount ofcargo and luggage load capacity. For example, if “XXX”amount equals 1400 lbs. and there will be

288 STARTING AND OPERATING

WARNING!Overloading of your tires is dangerous. Overloadingcan cause tire failure, affect vehicle handling, andincrease your stopping distance. Use ti

POWER WINDOWSThe power window controls are located on the driver’sdoor trim panel. There is a single switch on the frontpassenger door/rear doors whic

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread

check tire pressure. Do not make a visual judgementwhen determining proper inflation. Radial tires may lookproperly inflated even when they are under

Tire Pressures for High Speed OperationThe manufacturer advocates driving at safe speedswithin posted speed limits. Where speed limits or condi-tions

Radial-Ply TiresWARNING!Combining radial ply tires with other types of tireson your vehicle will cause your vehicle to handlepoorly. The instability c

Tread Wear IndicatorsTread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced.These indic

WARNING!Tires and spare tire should be replaced after sixyears, regardless of the remaining tread. Failure tofollow this warning can result in sudden

WARNING!• Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combina-tions of unapproved tires and wheels may cha

Improper alignment will not cause vehicle vibration.Vibration may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration

NOTE: For vehicles with optional wheel/tire sizes andsignificantly different tire placard pressures, the placardpressure value and the low-pressure th

CAUTION!After inspecting or adjusting the tire pressure al-ways reinstall the valve stem cap. This will preventmoisture and dirt from entering the val

INTRODUCTIONCONTENTS䡵 Introduction ... 4▫ Roll Over Warning ... 5䡵 How To Use This Manual ...

Auto DownBoth the driver and front passenger window switch hasan “Auto Down” feature. Press the window switch pastthe first detent, release, and the w

when a system fault is detected. The flash cycle willrepeat every ten minutes or until the fault condition isremoved and reset.The Tire Pressure Monit

Telltale Light” will illuminate continuously (solid) andshall remain illuminated until the warning condition isremoved/reset.NOTE: The “Tire Pressure

CAUTION!The TPMS has been optimized for the originalequipment tires and wheels. TPMS pressures havebeen established for the tire size equipped on your

General InformationThis device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions:•

TIRE ROTATION RECOMMENDATIONSTires on the front and rear axles of vehicles operate atdifferent loads and perform different steering, handling,and brak

FUEL REQUIREMENTS3.7/4.7L Engines (If Equipped)All engines (except 5.7L engines) are de-signed to meet all emissions regulationsand provide excellent

Over 40 auto manufacturer’s world wide have issued andendorsed consistent gasoline specifications (the World-wide Fuel Charter, WWFC) to define fuel p

MMT In GasolineMMT is a manganese containing metallic additive that isblended into some gasoline to increase octane. Gasolineblended with MMT provides

•An out-of-tune engine, or certain fuel or ignitionmalfunctions, can cause the catalytic converter tooverheat. If you notice a pungent burning odor or

•Guard against carbon monoxide with proper mainte-nance. Have the exhaust system inspected every timethe vehicle is raised. Have any abnormal conditio

WARNING!There is no anti-pinch protection when the windowis almost closed. Be sure to clear all objects from thewindow before closing.Resetting the Au

CAUTION!Damage to the fuel system or emission controlsystem could result from using an improper fuel cap(gas cap). A poorly fitting cap could let impu

Loose Fuel Filler Cap MessageIf the vehicle diagnostic system determines that the fuelfiller cap is loose, improperly installed, or damaged, a“CHECK G

WARNING!A fire may result if gasoline is pumped into aportable container that is inside of a vehicle. Youcould be burned. Always place gas containers

Gross Combination Weight Rating (GCWR)The gross combination weight rating (GCWR) is the totalpermissible weight of your vehicle and trailer whenweighe

hitches are the most popular on the market today andthey’re commonly used to tow small- and medium-sizedtrailers.Weight-Distributing HitchA weight-dis

Trailer Towing Weights (Maximum Trailer WeightRatings)The following chart provides the maximum trailerweight ratings towable for your given drivetrain

Note 1 – The trailer tongue weight must be considered aspart of the combined weight of occupants and cargo, andshould never exceed the weight referenc

NOTE: Remember that everything put into or on thetrailer adds to the load on your vehicle. Also, additionalfactory-installed options, or dealer-instal

WARNING!Improper towing can lead to an injury accident.Follow these guidelines to make your trailer towingas safe as possible:Make certain that the lo

2. GTW3. GAWR4. Tongue weight rating for the trailer hitch utilized(This requirement may limit the ability to alwaysachieve the 10% to 15% range of to

open or partially open positions. This is a normal occur-rence and can be minimized. If the buffeting occurs withthe sunroof open, adjust the sunroof

−An electronically actuated trailer brake controller isrequired when towing a trailer with electronicallyactuated brakes. When towing a trailer equipp

NOTE: Do not cut or splice wiring into the vehicleswiring harness.The electrical connections are all complete to the vehiclebut you must mate the harn

If using a manual transmission vehicle for trailer towing,all starts must be in FIRST gear to avoid excessive clutchslippage.Towing Tips — Automatic T

−City DrivingWhen stopped for short periods of time, put transmissionin neutral and increase engine idle speed.−Highway DrivingReduce speed.−Air Condi

Towing — Quadra–Trac II /Quadra–Drive II 4WDModelsCAUTION!Front or rear wheel lifts should not be used. Internaldamage to the transmission or transfer

“Electronic Vehicle Information Center (EVIC)” in Sec-tion 4 of this manual. (See page 186 for more informa-tion.)5. Start engine.6. Shift transmissio

CAUTION!Transmission damage may occur if the transmissionis shifted into P (Park) with the transfer case in N(Neutral) and the engine running. With th

5. Shift transmission into P (Park).6. Start the engine.7. Shift transmission into D (Drive).NOTE: When shifting out of transfer case N (Neutral),turn

CAUTION!Do not use a bumper mounted clamp-on tow bar onyour vehicle. The bumper face bar will be damaged.SNOW PLOWSnow plows, winches, and other after

WHAT TO DO IN EMERGENCIESCONTENTS䡵 Hazard Warning Flashers ...330䡵 If Your Engine Overheats ...331䡵 Jacking And Tire Chang

Research has shown that seat belts save lives, and theycan reduce the seriousness of injuries in a collision. Someof the worst injuries happen when pe

HAZARD WARNING FLASHERSYour vehicle’s hazard warning flasher is an emergencywarning system. When you activate it, all front and reardirectional signal

IF YOUR ENGINE OVERHEATSIn any of the following situations, you can reduce thepotential for overheating by taking the appropriate ac-tion.•On the high

JACKING AND TIRE CHANGINGWARNING!•Getting under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you.You could be crus

Spare Tire StowageThe spare tire is stowed under the rear of the vehicle bymeans of a cable winch mechanism. To remove or stowthe spare, use the jack

Spare Tire RemovalFit the jack handle extension over the drive nut. Use theLug Wrench to rotate the nut counter clockwise until thespare is on the gro

For example, if changing the right front tire, block theleft rear wheel.•Passengers should not remain in the vehicle when thevehicle is being jacked.J

4. Locate the jack as shown. For the front axle, place itunder the front lower control arm as shown. For the rearaxle, place it under the axle near th

WARNING!Raising the vehicle higher than necessary can makethe vehicle less stable. It could slip off the jack andhurt someone near it. Raise the vehic

NOTE: Tire should be stowed with the “beauty” sideup. Storing the tire upside down may result in scratchingor damage to the wheel face. Continue winch

5. Connect the other cable, first to the negative terminalof the booster battery and then connect the other end toa non-paint metal surface on the eng

Lap/Shoulder Belt Operating Instructions1. Enter the vehicle and close the door. Sit back andadjust the seat.2. The seat belt latch plate is above the

•Be sure your vehicle is not touching the jump startvehicle.•Observe all Battery Warnings in Section 7 of thismanual, while jump starting your vehicle

WARNING!Stand clear of vehicles when pulling with towhooks. Tow straps and chains may break, causingserious injury.TOWING A DISABLED VEHICLE2WD Models

MAINTAINING YOUR VEHICLECONTENTS䡵 3.7L Engine ...345䡵 4.7L Engine ...346䡵 5.7L Engine ...

▫ Air Conditioner Maintenance ...360▫ Power Steering Fluid Check ...361▫ Body Lubrication ...363▫ Windshield Wi

3.7L ENGINEMAINTAINING YOUR VEHICLE 3457

4.7L ENGINE346 MAINTAINING YOUR VEHICLE

5.7L ENGINEMAINTAINING YOUR VEHICLE 3477

ONBOARD DIAGNOSTIC SYSTEM — OBD IIYour vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe perfor

cap until a ⬙clicking⬙ sound is heard. This is an indicationthat the gas cap is properly tightened. Press the odometerreset button to turn the message

3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.”WARNING!A belt that is buckled into the wrong b

4. As soon as you turn your key to the ON position, youwill see your MIL symbol come on as part of a normalbulb check.5. Approximately 15 seconds late

DEALER SERVICEYour dealer has the qualified service personnel, specialtools and equipment to perform all service operations inan expert manner. Servic

could adversely affect the engine or vehicle performance.These items should be inspected if a malfunction isobserved or suspected.Engine OilChecking O

•More than 50% of your driving is at sustained highspeeds during hot weather, above 90°F (32°C)•Trailer towing•Taxi, Police, or delivery service (Comm

American Petroleum Institute (API) Engine OilIdentification SymbolThis symbol means that the oil hasbeen certified by the AmericanPetroleum Institute

Materials Added to Engine OilsThe manufacturer strongly recommends against the ad-dition of any additives (other than leak detection dyes) toengine oi

Belts should be inspected for evidence of cuts, cracks,glazing, or frayed cords and replaced if there is indicationof damage which could result in bel

CAUTION!Damage to the catalytic converter can result if yourvehicle is not kept in proper operating condition. Inthe event of engine malfunction, part

To minimize the possibility of catalytic converter damage:•Do not shut off the engine or interrupt the ignitionwhen the transmission is in gear and th

WARNING!The air cleaner can provide protection in the case ofengine backfire. Do not remove the air cleanerunless it is necessary for repair or mainte

4. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap portion, pull up abit on the shoulder belt. To loosen the l

To determine the battery charge, check the battery testindicator (if equipped) on top of the battery. Refer to theillustration.CAUTION!It is essential

WARNING!•Use only refrigerants and compressor lubricantsapproved by the manufacturer for your air condi-tioning system. Some unapproved refrigerants a

CAUTION!Do not use Automatic Transmission Fluid (ATF) orother types of power steering fluids when servicingthe power steering system of this vehicle.

Body LubricationLocks and all body pivot points, including such items asseat tracks, doors, tailgate and hood hinges, should belubricated periodically

The fluid reservoir for the windshield washers and therear window washer is shared. It is located in the front ofthe engine compartment (on the driver

Cooling SystemWARNING!You or others can be badly burned by hot antifreeze/coolant or steam from your radiator. If you see orhear steam coming from und

Cooling System — Drain, Flush, And RefillAt the intervals shown in the appropriate “MaintenanceSchedule,” the system should be drained, flushed, andre

Adding Engine CoolantYour vehicle has been built with an improved antifreeze/coolant that allows extended maintenance intervals. Thisantifreeze/coolan

The cap should be inspected and cleaned if there is anyaccumulation of foreign material on the sealing surfaces.WARNING!The warning words DO NOT OPEN

When additional antifreeze/coolant is needed to main-tain the proper level, it should be added to the coolantbottle. Do not overfill.Points To Remembe

6. To release the belt, push the red button marked PRESSon the buckle. The belt will automatically retract to itsstowed position. If necessary, slide

ONLY the correct type thermostat. Other designs mayresult in unsatisfactory cooling performance, poor gasmileage, and increased emissions.Hoses and Va

Brake and Power Steering System HosesWhen servicing the vehicle for scheduled maintenance,inspect surface of hoses for evidence of heat and me-chanica

fluid reservoir. With disc brakes, fluid level can beexpected to fall as the brake pads wear. However, lowfluid level may be caused by a leak and a ch

for correct fluid type. It is important that the transmissionfluid be maintained at the prescribed level using therecommended fluid.CAUTION!Using a tr

5. Remove the dipstick, wipe it clean and reinsert it untilseated.6. Remove the dipstick again and note the fluid level onboth sides. The fluid level

Special AdditivesThe manufacturer recommends against the addition ofany additives to the transmission. Exception to thispolicy is the use of special d

Front/Rear Axle FluidFront Axle Fluid Level CheckLubricant should be to the bottom of the oil fill hole.Rear Axle Fluid Level CheckLubricant should be

CAUTION!Under frequent heavy-duty driving conditions,change all lubricants and lubricate body compo-nents, all driveline joints and steering linkage m

•If insects, tar, or other similar deposits have accumu-lated on your vehicle, use Mopar威 Super Kleen Bugand Tar Remover to remove.•Use Mopar威 Cleaner

•Aluminum wheels should be cleaned regularly with amild soap and water to prevent corrosion. To removeheavy soil, use Mopar威 Wheel Cleaner or select a

As a guide, if you are shorter than average, you willprefer a lower position, and if you are taller than average,you’ll prefer a higher position. When

do not use polishes, oils, cleaning fluids, solvents, deter-gents, or ammonia based cleaners to clean your leatherupholstery. Application of a leather

Seat Belt MaintenanceDo not bleach, dye or clean the belts with chemicalsolvents or abrasive cleaners. This will weaken the fabric.Sun damage will als

Cavity Fuse/Color Description1 30 Amp Pink Audio Amp (B+)2 15 Amp Blue Sunroof (B+)3 10 Amp Red Htd Mirror (EBL)4 20 Amp Yellow Rr Pwr Out (B+)5 10 Am

Underhood Fuses (Power Distribution Center)Cavity Fuse/Color Description1 40 Amp Green HVAC Blower2 30 Amp Pink Power Outlets3 30 Amp Pink Rr Wiper/Ig

Cavity Fuse/Color Description20 20 Amp Yellow PCM Batt (Gasoline Only)21 30 Amp Pink ABS Valves22 Spare23 20 Amp Yellow FDCM24 20 Amp Yellow Fuel Pump

Underhood Fuses (Integrated Power Module)Cavity Fuse/Color Description1 Micro Relay Wiper On/Off Rly2 Micro Relay Wiper Hi/Lo Rly3 Micro Relay Horn Rl

Cavity Fuse/Color Description20 20 Amp Yellow FCM Batt #321 20 Amp Yellow Rt T-Tow Stop/Turn22 30 Amp Pink FDCM Mod23 50 Amp Red Rad Fan24 Mini Relay

REPLACEMENT BULBSInterior Lights Bulb TypeGlove Box Light ... 194Grab Handle Light ... L002825W5WOverhead Console R

FLUID CAPACITIESU.S. MetricFuel (Approximate) 20.6 Gallons 78 LitersEngine Oil with Filter3.7 Liter Engine (5W-30, API Certified) 5 Qts 4.7 Liters4.7

FLUIDS, LUBRICANTS, AND GENUINE PARTSEngineComponent Fluid, Lubricant, or Genuine PartEngine Coolant Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile For

This safety belt system has a retractor assembly that isdesigned to release webbing in a controlled manner. Thisfeature is designed to help reduce the

ChassisComponent Fluid, Lubricant, or Genuine PartAutomatic Transmission Mopar威 ATF+4 Automatic Transmission FluidTransfer Case (3.7L Engines) Mopar威

MAINTENANCE SCHEDULESCONTENTS䡵 Emission Control System Maintenance ...392䡵 Maintenance Schedules ...392▫ Schedule “B” ...

EMISSION CONTROL SYSTEM MAINTENANCEThe “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified toassure t

•Taxi, police, or delivery service (commercial service)•Off-road or desert driving•If equipped for and operated with E-85 (ethanol)fuel.NOTE: Most veh

•Check the windshield washer solvent, add as required.Once a Month•Check the tire pressure and look for unusual wear ordamage.•Inspect the battery and

Schedule “B”Follow this schedule if you usually operate your vehicleunder one or more of the following conditions.•Day or night temperatures are below

Miles 3,000 6,000 9,000 12,000 15,000(Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000)Change the engine oil and engine oil filter, if notreplac

Miles 18,000 21,000 24,000 27,000 30,000(Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000)Change the engine oil and engine oil filter, if notre

Miles 33,000 36,000 39,000 42,000 45,000(Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000)Change the engine oil and engine oil filter, if notre

Miles 48,000 51,000 54,000 57,000 60,000(Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000)Change the engine oil and engine oil filter, if notr

INTRODUCTIONThank you for selecting a Jeep威 Commander and wel-come to our worldwide family.This is a specialized utility vehicle designed for bothon-r

Enhanced Seat Belt Use Reminder System(BeltAlert)If the driver or front passenger seat belt has not beenbuckled within 60 seconds of starting the vehi

Miles 63,000 66,000 69,000 72,000 75,000(Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000)Change the engine oil and engine oil filter, if

Miles 78,000 81,000 84,000 87,000 90,000(Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000)Change the engine oil and engine oil filter, if

Miles 93,000 96,000 99,000 102,000 105,000(Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000)Change the engine oil and engine oil filter, i

Miles 108,000 111,000 114,000 117,000 120,000(Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000)Change the engine oil and engine oil filter

Miles 108,000 111,000 114,000 117,000 120,000(Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000)Flush and replace the engine coolant/anti-f

Schedule “A”Miles 6,000 12,000 18,000 24,000 30,000(Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000)[Months] [6] [12] [18] [24] [30]Change the

Miles 36,000 42,000 48,000 54, 000(Kilometers) (60 000) (70 000) (80 000) (90 000)[Months] [36] [42] [48] [54]Change the engine oil and engine oil fil

Miles 60,000 66,000 72,000 78,000(Kilometers) (100 000) (110 000) (120 000) (130 000)[Months] [60] [66] [72] [78]Change the engine oil and engine oil

Miles 84,000 90,000 96,000 102, 000(Kilometers) (140 000) (150 000) (160 000) (170 000)[Months] [84] [90] [96] [102]Change the engine oil and engine o

Miles 108,000 114,000 120,000(Kilometers) (180 000) (190 000) (200 000)[Months] [108] [114] [120]Change the engine oil and engine oil filter. X X XRot

The Enhanced Warning System (BeltAlert) can be reacti-vated by repeating this procedure.NOTE: Although the Enhanced Warning System(BeltAlert) has been

* This maintenance is not required if the belt waspreviously replaced.WARNING!You can be badly injured working on or around amotor vehicle. Do only th

IF YOU NEED CONSUMER ASSISTANCECONTENTS䡵 Suggestions For Obtaining Service For YourVehicle ...412▫ Prepare For The Appointm

SUGGESTIONS FOR OBTAINING SERVICE FORYOUR VEHICLEPrepare For The AppointmentIf you’re having warranty work done, be sure to have theright papers with

technicians, special tools, and the latest information toassure your vehicle is fixed correctly and in a timelymanner.This is why you should always ta

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY)To assist customers who have hearing difficulties, themanufacturer has installed specia

WARRANTY INFORMATION (U.S. Vehicles Only)See the Warranty Information Booklet for the terms andprovisions of DaimlerChrysler’s warranties applicable t

PUBLICATION ORDER FORMSTo order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Ex

Call Toll Free at:•1–800–890–4038 (U.S.)•1–800–387–1143 (Canada)OrVisit us on the World Wide Web at:•www.techauthority.daimlerchrysler.com•www.daimler

on specified government test surfaces of asphalt andconcrete. A tire marked C may have poor traction perfor-mance.WARNING!The traction grade assigned

INDEX10

Driver And Front Passenger SupplementalRestraint Systems (SRS)This vehicle has airbags for both the driver and rightfront passenger as a supplement to

ABS (Anti-Lock Brake System) ...179,271Adding Washer Fluid ... 169Adjustable Pedals ...147Air Cleaner,

Autostick ...258Auxiliary Electrical Outlet (Power Outlet) ... 162Auxiliary Power Outlet ... 162Battery .

Chains, Tire ... 303Changing A Flat Tire ... 332Chart, Tire Sizing ... 282Checks, Safe

Defroster, Rear Window ... 233Defroster, Windshield ... 71,234,241Diagnostic System, Onboard ...348Dimmer Sw

Block Heater ... 255Break-In Recommendations ...68Compartment ...346Cooling ...

Fluid Leaks ...71Fluid Level ChecksAutomatic Transmission ...372,373Engine Oil ... 352Po

Gear Ranges ...257General Information ... 24,303Glass Cleaning ...380Gross Axle Weight

Interior Lighting ...120Interior Lights ... 120,125Intermittent Wipers (Delay Wipers) ...128Introduct

Dimmer Switch, Headlight ... 122,126Electronic Stability Program (ESP)Indicator ... 140,180,183Electronic Throttle Cont

Liftgate, Tailgate ... 18Power Door ...20Lower Anchors and Tether for CHildren(LATCH) ...

This vehicle also is equipped with window bags toprotect the driver, front, and rear passengers sitting nextto a window. They are located above the si

Occupant Classification System (OCS) ...48Occupant Restraints ... 32Octane Rating, Gasoline (Fuel) ...305Odomete

PolishingandWaxing... 378PowerDistribution Center ...383Door Locks ... 20Mirrors ...

Recorder, Event Data ...56Recreational Towing ...323Shifting into Transfer Case Neutral (N) ...324Shifting o

Reminder ...183Shoulder Belt Anchorage ...37Seats ... 105Adjustment ...

Oil ... 353Speed Control (Cruise Control) ... 148Speedometer ... 178Starting ...

Inflation Pressures ...290Jacking ...332LifeofTires ... 294Load Capacity ...

TransmissionAutomatic ...256,372Maintenance ...372Range Indicator ...184Shifting ...

WindowsPower ...29Windshield Defroster ...71,234,241Windshield Washers ...127Fluid ...

438 INDEX

NOTES

The front airbags have a multi stage inflator design. Thisallows the airbag to have different rates of inflation thatare based on collision severity.

NOTES

Children that are not big enough to properly wear thevehicle seat belt should be secured in the rear seat, in achild restraint or belt-positioning boo

WARNING!•Relying on the airbags alone could lead to moresevere injuries in a collision. The airbags workwith your seat belt to restrain you properly.

•Driver and Front Passenger Seat Belt Pretensioner•Occupant Classification System (OCS) — Front Pas-senger Seat Only−Occupant Classification Module−Pa

WARNING!Ignoring the “Airbag Warning Light” in your instru-ment panel could mean you won’t have the airbagsto protect you in a collision. If the light

The “PAD Indicator Light” should not be illuminatedwhen teenagers, most children in a forward-facingchild restraint or booster seats, most children th

Roll Over WarningUtility vehicles have a significantly higher roll over ratethan other types of vehicles. This vehicle has a higherground clearance, h

Front PassengerSeat OccupantPassenger Air-bag Disable(PAD) IndicatorLightAirbag StatusAdult OFF ONGrocery Bags,Heavy Briefcasesand Other Rela-tively L

because this can also affect occupant classification. Also,if you fold down the rear seat check to be sure it doesn’ttouch the front passenger seat.If

The driver front airbag gas is vented through the ventholes in the sides of the airbag. The passenger frontairbag gas is vented through the vent holes

The front passenger seat assembly contains critical com-ponents that affect the front passenger airbag deploy-ment. Correctly functioning front passen

WARNING!Unapproved modifications or service procedures tothe front passenger seat assembly, its related compo-nents, or seat cover may inadvertently c

•As the airbags deflate you may see some smoke-likeparticles. The particles are a normal by-product of theprocess that generates the nontoxic gas used

Maintaining Your Airbag SystemWARNING!• Modifications to any part of the airbag system could cause it to failwhen you need it. You could be injured if

with other data gathered during a complete accidentinvestigation, the electronic data may be used byDaimlerChrysler Corporation and others to learn mo

Data Parameters that May Be Recorded:•Diagnostic trouble code(s) and warning lamp statusfor electronically-controlled safety systems, includingthe air

WARNING!In a collision, an unrestrained child, even a tinybaby, can become a missile inside the vehicle. Theforce required to hold even an infant on y

Failure to use driver and passenger seat belts providedis a major cause of severe or fatal injury. In fact, the U.S.government notes that the universa

WARNING!•Improper installation can lead to failure of aninfant or child restraint. It could come loose in acollision. The child could be badly injured

belt tight, however, any seat belt system will loosenwith time, so check the belt occasionally and pull ittight if necessary). For the second and thir

Older Children and Child RestraintsChildren who weigh more than 20 lbs (9 kg) and who areolder than one year can ride forward-facing in thevehicle. Fo

LATCH — Child Seat Anchorage System (LowerAnchors and Tether for CH ildren)Your vehicle’s second row seat is equipped with the childrestraint anchorag

The second row outboard seating positions have loweranchorages that are capable of accommodating LATCH-compatible child seats having flexible, webbing

In addition, there are tether strap anchorages behind eachrear outboard seating position located on the back of theseat.Many, but not all restraint sy

hook for attachment to the tether strap anchorage and ameans of adjusting the tension of the strap.You will first loosen the adjusters on the lower st

If the seat belt has a automatic locking retractor, it willhave a distinctive label. Pull the belt from the retractoruntil there is enough to allow yo

Route the tether strap over the seat back and attach thehook to the tether anchor located on the back of the seat.For the outboard seating positions,

The engine oil installed in the engine at the factory is ahigh quality energy conserving type lubricant. Oilchanges should be consistent with anticipa

WARNING!Engine exhaust, some of its constituents, and certainvehicle components contain or emit chemicalsknown to the State of California to cause can

•Do not inhale exhaust gases. They contain carbonmonoxide, a colorless and odorless gas which can kill.Never run the engine in a closed area, such as

DefrostersCheck operation by selecting the defrost mode and placethe blower control on high speed. You should feel the airdirected against the windshi

UNDERSTANDING THE FEATURES OF YOUR VEHICLECONTENTS䡵 Mirrors ...78▫ Inside Day/Night Mirror ...78▫ Inside Aut

▫ Front Seat Adjustment — Recline ...106▫ Manual Lumbar Support Adjustment ...106▫ Head Restraints ...107▫ 8 - Way Drive

▫ Lights-On Reminder ...125▫ Fog Lights — If Equipped ...126▫ Turn Signals ...126▫ High Beam Switch

䡵 Electronic Speed Control ...148▫ To Activate ...149▫ To Set At a Desired Speed ...149▫ To Deactiva

▫ Sunroof Fully Closed ...161䡵 Command-View™ Skylights — If Equipped ...161䡵 Power Outlet ...162䡵 Cup Holders

MIRRORSInside Day/Night MirrorThe mirror should be adjusted to center on the viewthrough the rear window. A two-point pivot systemallows for horizonta

Inside Automatic Dimming Mirror — If EquippedThis mirror automatically adjusts for annoying headlightglare from vehicles behind you. You can turn the

VEHICLE IDENTIFICATION NUMBERThe vehicle identification number (VIN) is found on alabel located on the left front corner of the instrumentpanel pad, v

Exterior Mirrors Folding FeatureAll exterior mirrors are hinged and may be moved eitherforward or rearward to resist damage. The hinges havethree dete

Power Remote Control Outside MirrorsThe power mirror switch is located on the driver’s doortrim panel next to the power door lock switch. A rotaryknob

Lighted Vanity Mirrors — If EquippedTo access a lighted vanity mirror, flip down one of thevisors.Lift the cover to reveal the mirror. The light will

UConnect™ allows you to transfer calls between thesystem and your cellular phone as you enter or exit yourvehicle, and enables you to mute the system’

The UConnect™ system can be used with any Hands-Free Profile certified Bluetooth™ cellular phone. Seewww.chrysler.com/uconnect for supported phones. I

example, you can either use the combined form voicecommand ⬙Phonebook New Entry,⬙ or you can breakthe combined form command into two voice com-mands:

NOTE:•www.chrysler.com/uconnect•www.dodge.com/uconnect•www.jeep.com/uconnectThe following are general phone to UConnect™ Systempairing instructions:•P

phones are present in the vehicle, the UConnect™system will use the priority 3 cellular phone when youmake a call. You can select to use a lower prior

•After the ⬙Ready⬙ prompt and the following beep, saythe name of the person you want to call. For example,you can say ⬙John Doe,⬙ where John Doe is a

four associated phone numbers and designations. Eachlanguage has a separate 32 name phonebook accessibleonly in that language.Edit Entries in the UCon

VEHICLE MODIFICATIONS / ALTERATIONSWARNING!Any modifications or alterations to this vehiclecould seriously affect its roadworthiness and safetyand may

•After you enter the Phonebook Delete menu, you willthen be asked for the name of the entry that you wishto delete. You can either say the name of a p

•To call one of the names in the list, press the ⬙VoiceRecognition’ button during the playing of the desiredname and say ⬙Call.⬙ NOTE: the user can al

Making a Second Call while Current Call inProgressTo make a second call while you are currently in a call,press the ’Voice Recognition’ button and say

Call TerminationTo end a call in progress, momentarily press the ⬘Phone’button. Only the active call(s) will be terminated and ifthere is a call on ho

•After the ⬙Ready⬙ prompt and the following beep, saythe name of the language you wish to switch to(English, Espanol, or Francais, if so equipped).•Co

Your phone must be turned on and paired to the UCon-nect™ system to allow use of this vehicle feature inemergency situations when the cell phone has n

When calling a number with your UConnect™ systemthat normally requires you to enter in a touch-tonesequence on your cellular phone keypad, you can pus

Dialing Using the Cellular Phone KeypadYou can dial a phone number with your cellular phonekeypad and still use the UConnect™ system (whiledialing via

Information ServiceWhen using AT&T Wireless Service, dialing to phonenumber ⬙#121,⬙ you can access voice activated automatedsystem to receive news

Select another Cellular PhoneThis feature allows you to select and start using anotherphone with the UConnect™ system. The phone musthave been previou